| 0 |
pdpServiceMaxMinValues units |
| 1 |
inH2O (68°F) |
| 2 |
inHg (0°C) |
| 3 |
ftH2O (68°F) |
| 4 |
mmH2O (68°F) |
| 5 |
mmHg (0°C) |
| 6 |
psi |
| 7 |
bar |
| 8 |
mbar |
| 9 |
g/cm2 |
| 10 |
kg/cm2 |
| 11 |
Pa |
| 12 |
kPa |
| 13 |
torr (0°C) |
| 14 |
atm |
| 15 |
inH2O (60°F) |
| 16 |
MPa |
| 17 |
inH2O (4°C) |
| 18 |
mmH2O (4°C) |
| 19 |
sensorTemperatureServiceMaxMinValues units |
| 20 |
°C |
| 21 |
°F |
| 22 |
°R |
| 23 |
K |
| 24 |
Vom Druckmesswerk erreichter Höchstwert |
| 25 |
Max. Druckwert |
| 26 |
.3f |
| 27 |
Vom Druckmesswerk erreichter Mindestwert |
| 28 |
Min. Druckwert |
| 29 |
Vom Messwerk für statischen Druck erreichter Mindestwert |
| 30 |
Mindestwert statischer Druck |
| 31 |
Vom Messwerk für statischen Druck erreichter Höchstwert |
| 32 |
Höchstwert statischer Druck |
| 33 |
Vom Temperaturmesswerk erreichter Mindestwert |
| 34 |
Min. Temperaturwert |
| 35 |
.2f |
| 36 |
Vom Temperaturmesswerk erreichter Höchstwert |
| 37 |
Max. Temperaturwert |
| 38 |
array ServiceMaxMin |
| 39 |
index array ServiceMaxMin |
| 40 |
reset customerMaxMinValues |
| 41 |
reset serviceMaxMinValues |
| 42 |
Prozessvariable auf gewünschten Wert setzen |
| 43 |
pdpBiasValue units |
| 44 |
Valore dell'Offset necessario per elevare o sopprimere la PV affinchè sia uguale a quella desiderata |
| 45 |
Offset Wert |
| 46 |
index array CustomerMaxMin |
| 47 |
Einheit |
| 48 |
Unit for digital output |
| 49 |
ft3/min |
| 50 |
gal/min |
| 51 |
L/min |
| 52 |
ImpGal/min |
| 53 |
m3/h |
| 54 |
ft/s |
| 55 |
m/s |
| 56 |
gal/s |
| 57 |
Million gal/d |
| 58 |
L/s |
| 59 |
MillionL/d |
| 60 |
ft3/s |
| 61 |
ft3/d |
| 62 |
m3/s |
| 63 |
m3/d |
| 64 |
ImpGal/h |
| 65 |
ImpGal/d |
| 66 |
mV |
| 67 |
Ohms |
| 68 |
Hz |
| 69 |
mA |
| 70 |
gal |
| 71 |
L |
| 72 |
ImpGal |
| 73 |
m3 |
| 74 |
ft |
| 75 |
m |
| 76 |
barrels |
| 77 |
in |
| 78 |
cm |
| 79 |
mm |
| 80 |
min |
| 81 |
s |
| 82 |
h |
| 83 |
d |
| 84 |
cST |
| 85 |
cP |
| 86 |
microS |
| 87 |
% |
| 88 |
V |
| 89 |
pH |
| 90 |
g |
| 91 |
kg |
| 92 |
t |
| 93 |
lb |
| 94 |
STon |
| 95 |
LTon |
| 96 |
mS/m |
| 97 |
microS/cm |
| 98 |
N |
| 99 |
N.m |
| 100 |
g/s |
| 101 |
g/min |
| 102 |
g/h |
| 103 |
kg/s |
| 104 |
kg/min |
| 105 |
kg/h |
| 106 |
kg/d |
| 107 |
t/min |
| 108 |
t/h |
| 109 |
t/d |
| 110 |
lb/s |
| 111 |
lb/min |
| 112 |
lb/h |
| 113 |
lb/d |
| 114 |
STon/min |
| 115 |
STon/h |
| 116 |
STon/d |
| 117 |
LTon/h |
| 118 |
LTon/d |
| 119 |
decaTherm |
| 120 |
SGU |
| 121 |
g/cm3 |
| 122 |
kg/m3 |
| 123 |
lb/gal |
| 124 |
lb/ft3 |
| 125 |
g/ml |
| 126 |
kg/L |
| 127 |
g/L |
| 128 |
lb/in3 |
| 129 |
STon/yd3 |
| 130 |
°Twad |
| 131 |
°Baum (hv) |
| 132 |
°Baum (lt) |
| 133 |
°API |
| 134 |
% sol/wt |
| 135 |
% sol/vol |
| 136 |
°Ball |
| 137 |
proof/vol |
| 138 |
proof/mass |
| 139 |
Bushel |
| 140 |
yd3 |
| 141 |
ft3 |
| 142 |
in3 |
| 143 |
in/s |
| 144 |
in/min |
| 145 |
ft/min |
| 146 |
deg/sec |
| 147 |
rps |
| 148 |
rpm |
| 149 |
m/h |
| 150 |
m3/h normal |
| 151 |
L/h normal |
| 152 |
ft3/min std |
| 153 |
bbl (liq) |
| 154 |
oz |
| 155 |
ft·lbf |
| 156 |
kW |
| 157 |
kW·h |
| 158 |
hp |
| 159 |
ft3/h |
| 160 |
m3/min |
| 161 |
barrels/s |
| 162 |
barrels/min |
| 163 |
barrels/h |
| 164 |
barrels/d |
| 165 |
gal/h |
| 166 |
ImpGal/s |
| 167 |
L/h |
| 168 |
ppm |
| 169 |
Mcalth/h |
| 170 |
MJ/h |
| 171 |
Btuth/h |
| 172 |
deg |
| 173 |
rad |
| 174 |
micro g/L |
| 175 |
icro g/m3 |
| 176 |
%Consistency |
| 177 |
% vol |
| 178 |
% stm qual |
| 179 |
Ft in Sixteenths |
| 180 |
ft3/lb |
| 181 |
pF |
| 182 |
ml/L |
| 183 |
micro l/L |
| 184 |
%Plato |
| 185 |
% Lower Explosion Level |
| 186 |
Mcalth |
| 187 |
Kohms |
| 188 |
MJ |
| 189 |
Btuth |
| 190 |
m3 normal |
| 191 |
L normal |
| 192 |
ft3 std |
| 193 |
ppb |
| 194 |
gal/d |
| 195 |
hl |
| 196 |
None |
| 197 |
Custom Unit |
| 198 |
Messende |
| 199 |
Upper limit for digital output |
| 200 |
Messanfang |
| 201 |
Lower limit for digital output |
| 202 |
Special unit |
| 203 |
Sondereinheit |
| 204 |
static Pressure New Value |
| 205 |
Messwerkstemperatur Trim Value |
| 206 |
Ermöglicht Vorort-Bedienung über Drucktasten |
| 207 |
Vorort-Bedienung |
| 208 |
Freigegeben |
| 209 |
Gesperrt |
| 210 |
Curve only for the variable to be displayed |
| 211 |
Kennlinientyp |
| 212 |
Linear |
| 213 |
Radizierung |
| 214 |
Xexp3/2 |
| 215 |
Xexp5/2 |
| 216 |
Linearisierungstabelle 22 Wertepaare |
| 217 |
Bidirektionale Radizierung |
| 218 |
Zylindrischer Tank, feste Tabelle |
| 219 |
Kugeltank, feste Funktion |
| 220 |
Unit of the variable to be displayed |
| 221 |
Upper Range of the variable to be displayed |
| 222 |
Lower Range of the variable to be displayed |
| 223 |
Display language |
| 224 |
Sprache |
| 225 |
Englisch |
| 226 |
Deutsch |
| 227 |
Französisch |
| 228 |
Spanisch |
| 229 |
Italienisch |
| 230 |
Display luminosity |
| 231 |
Kontrast |
| 232 |
Selection of the lines to be used for the display |
| 233 |
Anzeige-Modus |
| 234 |
Eine Zeile |
| 235 |
Eine Zeile + Balkendiagramm |
| 236 |
Zwei Zeilen |
| 237 |
Zwei Zeilen + Balkendiagramm |
| 238 |
Variable to be displayed on line 1 |
| 239 |
Ansicht Zeile 1 |
| 240 |
Druck |
| 241 |
Skalierter Ausgang |
| 242 |
Voltage Output |
| 243 |
Prozent Ausgang |
| 244 |
Messwerkstemperatur |
| 245 |
Statischer Druck |
| 246 |
HMI Skalierter Ausgang |
| 247 |
Harvester Percentage |
| 248 |
Battery Life |
| 249 |
Variable to be displayed on line 2 |
| 250 |
Ansicht Zeile 2 |
| 251 |
Variable to be represented on the bargraph |
| 252 |
Balkendiagramm-Ansicht |
| 253 |
|
| 254 |
Anzeige-Revision |
| 255 |
Nicht vorhanden |
| 256 |
1 |
| 257 |
2 |
| 258 |
3 |
| 259 |
4 |
| 260 |
5 |
| 261 |
6 |
| 262 |
7 |
| 263 |
8 |
| 264 |
9 |
| 265 |
10 |
| 266 |
11 |
| 267 |
12 |
| 268 |
13 |
| 269 |
14 |
| 270 |
15 |
| 271 |
16 |
| 272 |
17 |
| 273 |
18 |
| 274 |
19 |
| 275 |
20 |
| 276 |
21 |
| 277 |
22 |
| 278 |
23 |
| 279 |
24 |
| 280 |
25 |
| 281 |
26 |
| 282 |
27 |
| 283 |
28 |
| 284 |
29 |
| 285 |
30 |
| 286 |
31 |
| 287 |
32 |
| 288 |
33 |
| 289 |
34 |
| 290 |
35 |
| 291 |
36 |
| 292 |
37 |
| 293 |
38 |
| 294 |
39 |
| 295 |
40 |
| 296 |
41 |
| 297 |
42 |
| 298 |
43 |
| 299 |
44 |
| 300 |
45 |
| 301 |
46 |
| 302 |
47 |
| 303 |
48 |
| 304 |
49 |
| 305 |
50 |
| 306 |
51 |
| 307 |
52 |
| 308 |
53 |
| 309 |
54 |
| 310 |
55 |
| 311 |
56 |
| 312 |
57 |
| 313 |
58 |
| 314 |
59 |
| 315 |
60 |
| 316 |
61 |
| 317 |
62 |
| 318 |
63 |
| 319 |
64 |
| 320 |
65 |
| 321 |
66 |
| 322 |
67 |
| 323 |
68 |
| 324 |
69 |
| 325 |
70 |
| 326 |
71 |
| 327 |
72 |
| 328 |
73 |
| 329 |
74 |
| 330 |
75 |
| 331 |
76 |
| 332 |
77 |
| 333 |
78 |
| 334 |
79 |
| 335 |
80 |
| 336 |
81 |
| 337 |
82 |
| 338 |
83 |
| 339 |
84 |
| 340 |
85 |
| 341 |
86 |
| 342 |
87 |
| 343 |
88 |
| 344 |
89 |
| 345 |
90 |
| 346 |
91 |
| 347 |
92 |
| 348 |
93 |
| 349 |
94 |
| 350 |
95 |
| 351 |
96 |
| 352 |
97 |
| 353 |
98 |
| 354 |
99 |
| 355 |
100 |
| 356 |
101 |
| 357 |
102 |
| 358 |
103 |
| 359 |
104 |
| 360 |
105 |
| 361 |
106 |
| 362 |
107 |
| 363 |
108 |
| 364 |
109 |
| 365 |
110 |
| 366 |
111 |
| 367 |
112 |
| 368 |
113 |
| 369 |
114 |
| 370 |
115 |
| 371 |
116 |
| 372 |
117 |
| 373 |
118 |
| 374 |
119 |
| 375 |
120 |
| 376 |
121 |
| 377 |
122 |
| 378 |
123 |
| 379 |
124 |
| 380 |
125 |
| 381 |
126 |
| 382 |
127 |
| 383 |
128 |
| 384 |
129 |
| 385 |
130 |
| 386 |
131 |
| 387 |
132 |
| 388 |
133 |
| 389 |
134 |
| 390 |
135 |
| 391 |
136 |
| 392 |
137 |
| 393 |
138 |
| 394 |
139 |
| 395 |
140 |
| 396 |
141 |
| 397 |
142 |
| 398 |
143 |
| 399 |
144 |
| 400 |
145 |
| 401 |
146 |
| 402 |
147 |
| 403 |
148 |
| 404 |
149 |
| 405 |
150 |
| 406 |
151 |
| 407 |
152 |
| 408 |
153 |
| 409 |
154 |
| 410 |
155 |
| 411 |
156 |
| 412 |
157 |
| 413 |
158 |
| 414 |
159 |
| 415 |
160 |
| 416 |
161 |
| 417 |
162 |
| 418 |
163 |
| 419 |
164 |
| 420 |
165 |
| 421 |
166 |
| 422 |
167 |
| 423 |
168 |
| 424 |
169 |
| 425 |
170 |
| 426 |
171 |
| 427 |
172 |
| 428 |
173 |
| 429 |
174 |
| 430 |
175 |
| 431 |
176 |
| 432 |
177 |
| 433 |
178 |
| 434 |
179 |
| 435 |
180 |
| 436 |
181 |
| 437 |
182 |
| 438 |
183 |
| 439 |
184 |
| 440 |
185 |
| 441 |
186 |
| 442 |
187 |
| 443 |
188 |
| 444 |
189 |
| 445 |
190 |
| 446 |
191 |
| 447 |
192 |
| 448 |
193 |
| 449 |
194 |
| 450 |
195 |
| 451 |
196 |
| 452 |
197 |
| 453 |
198 |
| 454 |
199 |
| 455 |
200 |
| 456 |
201 |
| 457 |
202 |
| 458 |
203 |
| 459 |
204 |
| 460 |
205 |
| 461 |
206 |
| 462 |
207 |
| 463 |
208 |
| 464 |
209 |
| 465 |
210 |
| 466 |
211 |
| 467 |
212 |
| 468 |
213 |
| 469 |
214 |
| 470 |
215 |
| 471 |
216 |
| 472 |
217 |
| 473 |
218 |
| 474 |
219 |
| 475 |
220 |
| 476 |
221 |
| 477 |
222 |
| 478 |
223 |
| 479 |
224 |
| 480 |
225 |
| 481 |
226 |
| 482 |
227 |
| 483 |
228 |
| 484 |
229 |
| 485 |
230 |
| 486 |
231 |
| 487 |
232 |
| 488 |
233 |
| 489 |
234 |
| 490 |
235 |
| 491 |
236 |
| 492 |
237 |
| 493 |
238 |
| 494 |
239 |
| 495 |
240 |
| 496 |
241 |
| 497 |
242 |
| 498 |
243 |
| 499 |
244 |
| 500 |
245 |
| 501 |
246 |
| 502 |
247 |
| 503 |
248 |
| 504 |
249 |
| 505 |
250 |
| 506 |
251 |
| 507 |
252 |
| 508 |
253 |
| 509 |
254 |
| 510 |
255 |
| 511 |
resetPdpBias |
| 512 |
Grenze für die Verstärkung in der Nähe von Null |
| 513 |
Lin/Rad Übergang [%] |
| 514 |
Schleichmengenunterdrückung |
| 515 |
Nullrücker |
| 516 |
HW version major |
| 517 |
SW version major |
| 518 |
dummy_revision_byte0 |
| 519 |
dummy_revision_byte1 |
| 520 |
dummy_revision_byte2 |
| 521 |
sensor revision byte 0 |
| 522 |
sensor revision byte 1 |
| 523 |
sensor revision byte 2 |
| 524 |
Materiale della membrana bagnata sul lato meno |
| 525 |
Membranwerkstoff |
| 526 |
Monel |
| 527 |
Tantal |
| 528 |
Keramik |
| 529 |
AISI 316L Nichtrostender Stahl |
| 530 |
Hastelloy C276 |
| 531 |
Hastelloy C276 goldbeschichtet |
| 532 |
Monel goldbeschichtet |
| 533 |
PTFE Hastelloy |
| 534 |
Monel 400 |
| 535 |
|
| 536 |
Füllflüssigkeit des Messwerks |
| 537 |
Füllflüssigkeit |
| 538 |
Silikonöl |
| 539 |
Fluorkohlenstoff |
| 540 |
Weißöl (FDA) |
| 541 |
Inert (Galden) |
| 542 |
Glyzerin + H2O |
| 543 |
Santotherm |
| 544 |
Silikonöl Lebensmittelgeignet |
| 545 |
Pflanzenöl Neobee |
| 546 |
Dowtherm |
| 547 |
Ethyl Benzene |
| 548 |
Ethyl Alkohol |
| 549 |
Prophylene Glykol/Wasser |
| 550 |
ABB Füllung (dibutyl penthalate) |
| 551 |
Syltherm 800 |
| 552 |
Quecksilber |
| 553 |
DC97 9120 Pharma-B-Grade |
| 554 |
Mineralöl (Marcol 82) |
| 555 |
Hochtemperatur Silikonöl AN140 |
| 556 |
Niedrigtemperatur Silikonöl Syltherm XLT |
| 557 |
Inert (Halocarbon 4.2) |
| 558 |
Nicht benutzt |
| 559 |
Materiale della connessione di processo di un sensore di pressione relativa |
| 560 |
Werkstoff Prozessanschluss |
| 561 |
Kohlenstoffstahl |
| 562 |
AISI 304SS |
| 563 |
AISI 316 Nichtrostender Stahl |
| 564 |
Hastelloy C |
| 565 |
Kynar |
| 566 |
17-PH-17 |
| 567 |
Art Prozessanschluss auf Plusseite der Differenzmessumformer |
| 568 |
Anschlussart |
| 569 |
Konventionell |
| 570 |
Druckfühle |
| 571 |
Flanschdruckfühler mit Flachmembran |
| 572 |
Flanschdruckfühler mit Tubus |
| 573 |
Verschweißter Flansch |
| 574 |
Füllhöhe Sanitär |
| 575 |
Füllhöhe für Lebensmittel |
| 576 |
Direktanschluss |
| 577 |
Vollverschweißt für Druckfühler |
| 578 |
Abgedichtet für Druckfühler |
| 579 |
Druckfühler in Kompaktbauweise |
| 580 |
Innenliegende Membran |
| 581 |
Verschweißte Buchse |
| 582 |
Chemical T |
| 583 |
Mit Gewinde |
| 584 |
364 Flansch Typ |
| 585 |
Werkstoff Prozessanschluss auf Plusseite der Differenzmessumformer |
| 586 |
Kappenwerkstoff |
| 587 |
AISI 304SS |
| 588 |
Duplex SS |
| 589 |
Werkstoff messstoffberührte Dichtung auf Plusseite der Differenzmessumformer |
| 590 |
Werkstoff O-Ring |
| 591 |
AISI 316 SS |
| 592 |
PTFE |
| 593 |
Viton |
| 594 |
Buna-N |
| 595 |
Ethyl Prop. |
| 596 |
Nitril Gummi (Perbunan NBR) |
| 597 |
Aluminium |
| 598 |
TFE Glasgefüllt |
| 599 |
Perfluor Elastomer |
| 600 |
EPDM |
| 601 |
Graphite |
| 602 |
Silikongummi |
| 603 |
Garlock |
| 604 |
Materiale della spina sul lato più di un sensore di pressione differenziale |
| 605 |
Verschlussstopfen |
| 606 |
Anzahl der Druckfühler |
| 607 |
Nummer |
| 608 |
Ein |
| 609 |
Zwei |
| 610 |
Einer Minusseite |
| 611 |
Einer Plusseite |
| 612 |
Type of remote seal on the side H of the Sensor |
| 613 |
Typ |
| 614 |
Zellenbauweise |
| 615 |
Gewindeanschluss innenliegende Membran |
| 616 |
Chemical T |
| 617 |
Membrankleindruckfühler |
| 618 |
Triclamp & Cherry Burrell |
| 619 |
Lebensmittel (Überwurfmutter) |
| 620 |
Kleindruckfühler |
| 621 |
Aseptisch |
| 622 |
Flanschanschluss innenliegende Membran |
| 623 |
Bündige Sanitärmembran |
| 624 |
Sanitärmembran mit Tubus |
| 625 |
Flacher Flansch |
| 626 |
Flansch mit Tubus |
| 627 |
Harnstoffverarbeitung |
| 628 |
Pulp & Paper |
| 629 |
Getränk |
| 630 |
Monel |
| 631 |
Tantalum |
| 632 |
AISI 316L Stainless Steel |
| 633 |
Inconel |
| 634 |
Hastelloy C276 |
| 635 |
AISI 316L TFE Coated |
| 636 |
Monel Gold Plated |
| 637 |
Hastelloy C276 TFE Coated |
| 638 |
Monel 400 |
| 639 |
Inert (Galden) |
| 640 |
Glyzerin + H2O |
| 641 |
Hochtemperatur Silikonöl (AN140) |
| 642 |
Niedrigtemperatur Silikonöl (Syltherm XLT) |
| 643 |
Hochtemperatur Silikonöl (DC740) |
| 644 |
Silikonöl (Baysilone M5 / 5 Cts) |
| 645 |
Silikonöl (DC200/ 10 Cts) |
| 646 |
Mineralöl (Marcol 122) |
| 647 |
Galden HT55 |
| 648 |
Type of remote seal on the side L of the Sensor |
| 649 |
boltMaterial highSide |
| 650 |
nuteltMaterial highSide |
| 651 |
DrainVentposition highSide |
| 652 |
Der aktuelle Messwert entspricht: |
| 653 |
pdpValue units |
| 654 |
Maximum Working Pressure Units - The units of the Maximum working pressure |
| 655 |
maxWorkingPressure units |
| 656 |
Maximale Druckgrenze, in der das Messwerk kompensiert wird. |
| 657 |
Max. Betriebsdruck |
| 658 |
serialNo Part0 |
| 659 |
serialNo Part1 |
| 660 |
serialNo Part2 |
| 661 |
serialNo Part2a |
| 662 |
serialNo Part3 |
| 663 |
serialNo Part4 |
| 664 |
02u |
| 665 |
serialNo Part5 |
| 666 |
serialNo Part6 |
| 667 |
serialNo Part7 |
| 668 |
serialNo Part8 |
| 669 |
000006u |
| 670 |
serialNo Part9 |
| 671 |
serialNo Part10 |
| 672 |
serialNo Part11 |
| 673 |
2d |
| 674 |
opCode ResetToCustomerTrimming |
| 675 |
opCode SaveTrimmingAsFactory |
| 676 |
opCode SaveTrimmingAsCustomer |
| 677 |
Reset Sensor Trimming |
| 678 |
Sensor communication error |
| 679 |
resetToDefault |
| 680 |
toDefaultOper |
| 681 |
subsystemIndex |
| 682 |
dataclassIndex |
| 683 |
Update Rate Service Status |
| 684 |
OFF |
| 685 |
ACTIVE |
| 686 |
NEGOTIATING |
| 687 |
SWITCHING OFF |
| 688 |
REJECTED |
| 689 |
Update Rate Service Code |
| 690 |
OK |
| 691 |
ACCESS RESTRICTED |
| 692 |
BUSY |
| 693 |
INITIATED |
| 694 |
RUNNING |
| 695 |
DEAD |
| 696 |
CONFLICT |
| 697 |
DENIED |
| 698 |
UNKNOW FLAG |
| 699 |
UNKNOW DOMAIN |
| 700 |
UNKNOW NICKNAME |
| 701 |
NOT INITIALIZED |
| 702 |
TO BE CREATED |
| 703 |
TO BE DELATED |
| 704 |
NO RESPONSE |
| 705 |
Max Update Rate Service Status |
| 706 |
Max Update Rate Service Code |
| 707 |
Device Status |
| 708 |
Function Check |
| 709 |
Out of Specs |
| 710 |
Maintenance Required |
| 711 |
Failure |
| 712 |
diagnosticsConditionNumber |
| 713 |
diagnosticsConditionDetailsClass |
| 714 |
diagnosticsConditionDetailsGroup |
| 715 |
diagnosticsConditionDetailsPriority |
| 716 |
diagnosticsConditionDetailsAlarmCounter |
| 717 |
diagnosticsConditionDetailsAlarmTimeCounterDay |
| 718 |
diagnosticsConditionDetailsAlarmTimeCounterMsec |
| 719 |
diagnosticsConditionDetailsTimeStampLastAlarmDay |
| 720 |
diagnosticsConditionDetailsTimeStampLastAlarmMsec |
| 721 |
diagnosticsConditionDetailsCodes0 |
| 722 |
diagnosticsConditionDetailsCodes1 |
| 723 |
diagnosticsConditionDetailsCodes2 |
| 724 |
diagnosticsConditionDetailsCodes3 |
| 725 |
Diag Simulation enable |
| 726 |
By enabling diagnostics simulation, any one diagnostics can be simulated at a time. Actual device diagnostics are not reported when diagnostics simulation is turned ON |
| 727 |
Aus |
| 728 |
Ein |
| 729 |
Diagnosis Simulation |
| 730 |
Battery Level |
| 731 |
Messwerk ungültig |
| 732 |
Messwerk-Speicherfehler |
| 733 |
Speicherfehler |
| 734 |
P-dP Messwerkfehler |
| 735 |
Fehler Messwerk statischer Druck |
| 736 |
Fehler Messwerk-Temperatur |
| 737 |
Funkausfall |
| 738 |
beitreten Status |
| 739 |
P-dP außerhalb der Grenzwerte |
| 740 |
Statischer Druck außerhalb der Grenzwerte |
| 741 |
Messwerktemperatur außerhalb der Grenzwerte |
| 742 |
Max. Arbeitsdruck überschritten |
| 743 |
Primary variable Out of High Range |
| 744 |
Primary variable Out of Low Range |
| 745 |
Messwerk-Temperatursimulation aktiv |
| 746 |
Statische Drucksimulation aktiv |
| 747 |
P-dP Simulation aktiv |
| 748 |
skalierten Ausgang Simulation aktiv |
| 749 |
Fehler im stromausfallsicheren Speicher |
| 750 |
Electronic Temperature out of Limit |
| 751 |
Replace info |
| 752 |
Falsche Gerätekonfiguration |
| 753 |
Parameterübertragung erforderlich-Beide Richtungen gültig |
| 754 |
diagnostics Masking |
| 755 |
Primärvariable außerhalb des Bereichs |
| 756 |
Fehler elektronische Schnittstelle |
| 757 |
Druck-Bereichsüberschreitung |
| 758 |
|
| 759 |
Analogausgang gesättigt |
| 760 |
Unzuverlässiger Ausgangsstrom |
| 761 |
Warnung Spannungsversorgung |
| 762 |
Konfigurationsfehler |
| 763 |
PILD-Ausgang |
| 764 |
Geänderte Betriebsbedingungen |
| 765 |
Falscher Ausgangsstrom |
| 766 |
Elektronik-Temperatur außerhalb der Grenzwerte |
| 767 |
Anzahl Hochfahren |
| 768 |
Anzahl Versorgungsspannung Ein |
| 769 |
Total Working time_day |
| 770 |
Total Working time_sec |
| 771 |
Partial Working time_0 |
| 772 |
Partial Working time_1 |
| 773 |
Typ des Messwerks |
| 774 |
Messwerkstyp |
| 775 |
Differenzdruck |
| 776 |
Absolutdruck |
| 777 |
Überdruck |
| 778 |
pdpSensor units |
| 779 |
Minimum value for range limits |
| 780 |
Untere Messbereichsgrenze |
| 781 |
Maximum value for range limits |
| 782 |
Obere Messbereichsgrenze |
| 783 |
Minimum difference between URV and LRV |
| 784 |
Kleinste Spanne |
| 785 |
Hardware Revision |
| 786 |
sensorTechnology |
| 787 |
boltMaterial_LowSide |
| 788 |
nuteMaterial LoSide |
| 789 |
drainVentPosition LoSide |
| 790 |
moutingThread |
| 791 |
applicationType |
| 792 |
pdpCustomerMaxMinValues units |
| 793 |
staticPressureCustomerMaxMinValues units |
| 794 |
sensorTemperatureCustomerMaxMinValues units |
| 795 |
array CustomerMaxMin |
| 796 |
Ausgang im Fehlerfall |
| 797 |
Auswahl von Hochalarm oder Tiefalarm |
| 798 |
Höhe |
| 799 |
Niedrig |
| 800 |
Untere Grenze des analogen Ausgangsstroms |
| 801 |
Minimalstrom |
| 802 |
Vdc |
| 803 |
Obere Grenze des analogen Ausgangsstroms |
| 804 |
Maximalstrom |
| 805 |
Wert für den Tiefalarmstrom (< 1Vdc) im Fehlerfall |
| 806 |
Tiefalarmstrom |
| 807 |
Wert für den Hochalarmstrom (> 5Vdc) im Fehlerfall |
| 808 |
Hochalarmstrom |
| 809 |
Alarmsteuerung |
| 810 |
Steuerung des Alarmverhaltens über DIP-Schalter oder Bedienprogramm |
| 811 |
Hardware Fail Safe Type |
| 812 |
Software Fail Safe Type |
| 813 |
Identifizieren |
| 814 |
Gerät |
| 815 |
Zusätzliche Geräte-Revisionen |
| 816 |
Messstelle |
| 817 |
Zusatzinformation |
| 818 |
Detailed Setup |
| 819 |
Allgemeines |
| 820 |
Messwerk Setup |
| 821 |
P-dP Messwerk |
| 822 |
Statisches Druckmesswerk |
| 823 |
Betriebsgrenzen |
| 824 |
Werkstoffe Messwerk |
| 825 |
Prozessanschluss Plusseite |
| 826 |
Prozessanschluss Minusseite |
| 827 |
Grundwerkstoffe Messwerk |
| 828 |
Messwerk |
| 829 |
Druckfühler |
| 830 |
Anzahl |
| 831 |
Plusseite |
| 832 |
Minusseite |
| 833 |
P-dP |
| 834 |
Prozessvariable |
| 835 |
Gemessener Wert |
| 836 |
Skalierung |
| 837 |
Werteingabe |
| 838 |
Prozessdruckübernahme |
| 839 |
Prozessvariable Offset (Bias) |
| 840 |
Parallelverschiebung |
| 841 |
Übertragungsfunktion |
| 842 |
Einstellung Radizierung |
| 843 |
Ausgang |
| 844 |
Filter |
| 845 |
HART Zuordnung |
| 846 |
HART Indicatore |
| 847 |
Anzeige-Einstellung |
| 848 |
Display-Skalierung |
| 849 |
Bedienen |
| 850 |
Extras |
| 851 |
Zurücksetzen |
| 852 |
Rücksetzen |
| 853 |
Werkseinstellungen laden |
| 854 |
Simulation |
| 855 |
Kalibrieren |
| 856 |
Drucksensor |
| 857 |
Diagnose |
| 858 |
Diagnoseüberwachung |
| 859 |
Elektronik |
| 860 |
Sensor/Antriebe |
| 861 |
Einbau/Inbetriebnahme |
| 862 |
Prozess |
| 863 |
Betriebsbedingungen |
| 864 |
Konfiguration |
| 865 |
Historien-Information |
| 866 |
Protokollierung Druckvariable |
| 867 |
Protokollierung Temperaturmesswerk |
| 868 |
Protokollierung statischer Druck |
| 869 |
Electronics |
| 870 |
Sensor / Actuator |
| 871 |
Installation / Startup |
| 872 |
Operating conditions |
| 873 |
Process |
| 874 |
Stromausgang |
| 875 |
Alarmverhalten |
| 876 |
Stromgrenzen |
| 877 |
Alarmstrom |
| 878 |
Offline |
| 879 |
Kommunikationsart |
| 880 |
Stromausgang |
| 881 |
Skalierter |
| 882 |
Schreibschutz |
| 883 |
Beobachten |
| 884 |
Trend |
| 885 |
Device Icon |
| 886 |
Analog Output |
| 887 |
Bereich |
| 888 |
Prozessvariable auf Null setzen |
| 889 |
Freigabe Setzen Prozessvariable = 0,0 |
| 890 |
Set PV Val |
| 891 |
Freigabe des Betriebs mit neuer Prozessvariablen |
| 892 |
PV Bias Reset |
| 893 |
PV Scaling Reset method - P-dP Bias will be Reset |
| 894 |
Enable Parallel Shift operation |
| 895 |
Full trim method - The full trimming allows the performance of high or low trim |
| 896 |
Full trim |
| 897 |
Messwerkstemperatur Trimming |
| 898 |
LO trim method - Allows the performance low trim |
| 899 |
Low trim |
| 900 |
Rücksetzen auf Feineinstellung User-Messwerk |
| 901 |
Konfiguration geändert |
| 902 |
Flag Gerätekonfiguration geändert rücksetzen |
| 903 |
Als Feineinstellung User-Messwerk speichern |
| 904 |
Save the actual sensor trimming as User Trimming |
| 905 |
Messwerk-Feineinstellung auf Werkseinstellungen rücksetzen |
| 906 |
Messwerk-Feineinstellung auf Werkseinstellungen rücksetzen |
| 907 |
Aborting Input Simulation |
| 908 |
Feldgeräterevision |
| 909 |
Software Revision |
| 910 |
Feldgeräterevision |
| 911 |
Messwerksrevision |
| 912 |
More Info |
| 913 |
More Information Available: input simulation |
| 914 |
More Info: |
| 915 |
More Information Available:primary value |
| 916 |
Hours |
| 917 |
sec |
| 918 |
Betriebszeit insgesamt |
| 919 |
Betriebsdauer des Geräts |
| 920 |
Clear Other Diag Simulation |
| 921 |
Change SV Mapping |
| 922 |
Change TV Mapping |
| 923 |
Change QV Mapping |
| 924 |
P-dP |
| 925 |
Physikalische Einheit |
| 926 |
Harvester Percentage |
| 927 |
Battery Life |
| 928 |
Seriennummer |
| 929 |
Eindeutige Seriennummer |
| 930 |
Read Sensor Sl Number |
| 931 |
Messanfang setzen |
| 932 |
Prozesswert für Messanfang |
| 933 |
Messende setzen |
| 934 |
Ausführen |
| 935 |
Ausführung der Parallelverschiebung |
| 936 |
Neuer Offset Wert |
| 937 |
Gewünschter Wert für den Ausgang |
| 938 |
Press Sim Val |
| 939 |
Druck Simulation |
| 940 |
StPress Sim Val |
| 941 |
Statische Drucksimulation |
| 942 |
Sens Temp Sim Val |
| 943 |
Messwerk-Temperatursimulation |
| 944 |
Scaledout Sim Val |
| 945 |
ScaledOut Simulation |
| 946 |
Simulation |
| 947 |
method to Enable simulation |
| 948 |
squawk_abort_label |
| 949 |
Start Squawk |
| 950 |
Druck Eingang |
| 951 |
Definition of High (+) and Low (-) sides of the Pressure Inputs |
| 952 |
Direkt |
| 953 |
Umgekehrt |
| 954 |
Messwerkspolarität |
| 955 |
Local DeviceSerialNumber |
| 956 |
Voltage Trimming |
| 957 |
Voltage Simulation |
| 958 |
Burst Command |
| 959 |
Cmd 2: %range |
| 960 |
Percent of Range of the Primary Variable |
| 961 |
Cmd 3: Dyn vars |
| 962 |
All Dynamic Process Variables |
| 963 |
Read Device Variables with Status- This commands allows up to 8 device variables (along with status and quality information for each) to be read in burst mode. The device variables to be burst are set using Command 107 |
| 964 |
Cmd 48: Read Additional Device Status |
| 965 |
Read Additional Device - This command reads additional device status information |
| 966 |
Update period for burst message |
| 967 |
5.3f |
| 968 |
Max Update Period |
| 969 |
Maxium update period for burst message |
| 970 |
Wireless HART Enabled |
| 971 |
Enabled on WirelessHART device connection only |
| 972 |
Burst Msg Trigger Mode |
| 973 |
Burst Trigger Class |
| 974 |
Burst Trigger Units |
| 975 |
Burst Trigger Level |
| 976 |
Burst Variable Code 1 |
| 977 |
Burst Variable Slot - Device variable code assigned to the slot to be read in burst mode. |
| 978 |
P-dp |
| 979 |
Electronic Temperature |
| 980 |
pdp trim |
| 981 |
Burst Variable Code 2 |
| 982 |
Burst Variable Code 3 |
| 983 |
Burst Variable Code 4 |
| 984 |
Burst Variable Code 5 |
| 985 |
Burst Variable Code 6 |
| 986 |
Burst Variable Code 7 |
| 987 |
Burst Variable Code 8 |
| 988 |
Ausgangs-Feineinstellung auf Werkseinstellungen rücksetzen |
| 989 |
Feineinstellung D/A-Wandlerausgang auf Werkseinstellungen rücksetzen |
| 990 |
266 P-dP 1...5 Vdc |
| 991 |
Wireless Signal Found |
| 992 |
Network packets have been recognized |
| 993 |
Wi Signal Identified |
| 994 |
Wi Time Synchronized |
| 995 |
Advertisement Heard |
| 996 |
Join Requested |
| 997 |
Set on transmission of first join request |
| 998 |
Join Retrying |
| 999 |
Set after the first join request retry (i.e. when number of join requests > 2). Cleared when device is authenticated or when Active Search started. |
| 1000 |
Join Failed |
| 1001 |
Set on transition from Active Search mode to Deep Sleep mode. Cleared on transition from Deep Sleep to Active Search. |
| 1002 |
Nw Secy Cl Granted |
| 1003 |
Network Manager Session Established |
| 1004 |
Network Joined |
| 1005 |
Network Joined. Normal superframe and links obtained. |
| 1006 |
Nw Bw Requested |
| 1007 |
Negotiating Network Properties. Gateway session obtained. |
| 1008 |
Join Complete |
| 1009 |
Normal operating mode. |
| 1010 |
Out of Specification |
| 1011 |
Device Configuration Locked |
| 1012 |
Status Simulaiton Active |
| 1013 |
Discrete Variable Simulation Active |
| 1014 |
Event Notification Overflow |
| 1015 |
Sub-Device Mismatch |
| 1016 |
Sub-Devices with Duplicate IDs Found |
| 1017 |
Stale Data Notice |
| 1018 |
Radio Failure |
| 1019 |
Für Datensatz oder Gerät |
| 1020 |
Geräte Revision |
| 1021 |
Kommunikationsname |
| 1022 |
........ |
| 1023 |
Beschreibung |
| 1024 |
Datum |
| 1025 |
Endmontagenummer |
| 1026 |
Adresse |
| 1027 |
Geräteadresse in der Anwendung. |
| 1028 |
Zusatzinformation |
| 1029 |
HART-Revision |
| 1030 |
Universalkommando Geräterevisio |
| 1031 |
Possible Cause :Mechanical damage to the sensor. Loss of fill fluid from the cell; ruptured diaphragm..
Suggested Action :The sensor must be replaced. |
| 1032 |
Possible Cause :The circuitry for the sampling of the static pressure has failed.
Suggested Action : The sensor must be replaced. |
| 1033 |
Possible Cause :The circuitry for the sampling of the temperature has failed.
Suggested Action :The sensor must be replaced. |
| 1034 |
Reserved |
| 1035 |
|
| 1036 |
Possible Cause :The measurement range has not been correctly calculated OR an incorrect transducer model has been selected.
Suggested Action :The compatibility of pressure transmitter model and process conditions has to be checked. Probably a different transmitter type is required. |
| 1037 |
Possible Cause :The static pressure of the process exceeds the limit of the sensor. Exceeding the Static Pressure can reduce accuracy, mechanically damage the diaphragm and may require calibration/replacement. An incorrect transducer model could have been selected.
Suggested Action :The compatibility of pressure transmitter model and process conditions has to be checked. Probably a different transmitter type is required. |
| 1038 |
Possible Cause :The temperature of the process environment affects the pressure transmitter; Excess temperature can reduce accuracy, degrade device components and may require calibration/replacement.
Suggested Action :The compatibility of pressure transmitter model and process conditions has to be checked. A different installation type could be required e.g. use of remote seals. |
| 1039 |
Possible Cause: Critical low level of battery reached
Suggested Action: Change Battery |
| 1040 |
Join Fail |
| 1041 |
Possible Causes:
1. Join key may be wrong
2.Network ID may be wrong
3. Adapter has some issue
4. No wireless communication
Suggested Action:
1. Re-enter correct join key
2. Re-enter correct Network ID
3. Reset the device
4. Look into wireless HART Connection mask |
| 1042 |
Possible Cause: Radio chip / Antenna defect
Suggested Action:
1. Restart wireless device
2. check antenna
if the error persist, replace antenna and/or electronics |
| 1043 |
Possible Cause :Sensor memory corrupted.
Suggested Action :The Sensor must be replaced. |
| 1044 |
Possible Cause :Writings to the Sensor non-Volatile Memory was not successful.
Suggested Action :The Sensor should be replaced as soon as possible. |
| 1045 |
Possible Cause :Exchange of data between Electronics and Sensor have problems.
Suggested Action :Power cycle the device and retry the operation, if the error persist the electronics should be replaced as soon as possible. |
| 1046 |
Speicherfehler |
| 1047 |
Possible Cause :Electronic memory corrupted.
Suggested Action :The electronics must be replaced. |
| 1048 |
Possible Cause :Writings to the electronic non-Volatile Memory was not successful.
Suggested Action :The electronics should be replaced as soon as possible. |
| 1049 |
Simulation aktiv |
| 1050 |
Possible Cause :The static pressure of the process exceeds the limit of the max working Pressure supported by the transmitter. Exceeding the Max Working Pressure can mechanically damage the process connections (flanges, pipes....) and/or be dangerous .
Suggested Action :The compatibility of the process connection type and material with process conditions has to be checked. A different installation type could be required e.g. use of remote seals. |
| 1051 |
Possible Cause :This effect could be produced by other equipment on the process, (valves.....). Exceeding the pressure range can cause reduced accuracy or mechanical damage to the diaphragm material and may require calibration/replacement.
Suggested Action :The compatibility of pressure transmitter model and process conditions has to be checked. A different transmitter type could be required . |
| 1052 |
Schleifentest |
| 1053 |
Possible Cause :The analog and digital analog outputs for the Primary Variable are held at the requested value. Device is in fixed current (Loop Test) mode.
Suggested Action :Use a HART configurator to place device back into normal operating mode (Remove from Loop Test - Fixed output mode). |
| 1054 |
Possible Cause :Process conditions have changed to an extent that new settings for the PILD algorithm are needed.
Suggested Action :A new Training is necessary for this new process condition. |
| 1055 |
PILD-Ausgang |
| 1056 |
Possible Cause :The output circuit could be broken or not correctly calibrated.
Suggested Action :Perform an Output Trimming and if the error persist the electronics must be replaced. |
| 1057 |
The Electronics or the Sensor have been changed,but the replacement operation has not been executed |
| 1058 |
QV ist |
| 1059 |
New Lower range push upper range out of sensor limits |
| 1060 |
Burstkommando |
| 1061 |
Hart-Kommando zum Lesen im Burstmodus |
| 1062 |
Kommando 1 |
| 1063 |
Kommando 2 |
| 1064 |
Kommando 3 |
| 1065 |
Warning! Burst Condition conflict:Burst Triger is set to Continuous |
| 1066 |
Invalid burst message |
| 1067 |
Invalid device variable classification |
| 1068 |
Invalid burst trigger mode selection code |
| 1069 |
Output voltage in Vdc |
| 1070 |
Transfer Function |
| 1071 |
Ausgang im Fehlerfall |
| 1072 |
Alarm mit Analogausgang |
| 1073 |
Squawk Control |
| 1074 |
Off |
| 1075 |
On |
| 1076 |
Squack once |
| 1077 |
PdP Value |
| 1078 |
Pressure -Diffrenetial Pressure |
| 1079 |
Minimum Span |
| 1080 |
7d |
| 1081 |
Physikalische Einheit für den Prozessdruck |
| 1082 |
Damp an irregular signal |
| 1083 |
Dämpfung |
| 1084 |
.1f |
| 1085 |
Size |
| 1086 |
classification |
| 1087 |
PdP Status |
| 1088 |
Pres LS |
| 1089 |
Pres Fmly stat |
| 1090 |
PdP trimPointCode |
| 1091 |
pdpSensortrim units |
| 1092 |
Aktueller Wert der Referenz |
| 1093 |
Unterer Abgleichpunkt |
| 1094 |
Oberer Abgleichpunkt |
| 1095 |
Enable Simulation |
| 1096 |
Disable |
| 1097 |
Enable |
| 1098 |
Update time Period label |
| 1099 |
No Trim Points Supported |
| 1100 |
Lower Trim Point Supported |
| 1101 |
Upper Trim Point Supported |
| 1102 |
Lower and Upper Trim Points Supported |
| 1103 |
Device Family |
| 1104 |
StaticPr Value |
| 1105 |
Einheit, in der die Bereichswerte angezeigt werden |
| 1106 |
Einheit stat. Druck |
| 1107 |
StaticPressureTrimValue units |
| 1108 |
StaticPr Status |
| 1109 |
ScaledOut Status |
| 1110 |
Sensor Temp Status |
| 1111 |
sp trimPointCode |
| 1112 |
Sensor Serial Number |
| 1113 |
Static Pressure Collection |
| 1114 |
Sensor Temp value |
| 1115 |
Die Messwerkstemperatur wird in dieser Einheit angezeigt |
| 1116 |
Temperatureinheit |
| 1117 |
Sensor Temperature Damping |
| 1118 |
Max. Betriebstemperatur |
| 1119 |
Maximum limit of temperature within the sensor is compensated as from data sheet |
| 1120 |
Min. Betriebstemperatur |
| 1121 |
Minimum limit of temperature within the sensor is compensated as from data sheet |
| 1122 |
TemperatureTrimValue units |
| 1123 |
st trimPointCode |
| 1124 |
SensorTemp Collection |
| 1125 |
communicationScaleOutValue units |
| 1126 |
Skalierter Ausgang |
| 1127 |
devVar3 Value |
| 1128 |
devVar3 Damping |
| 1129 |
Scaledout USL |
| 1130 |
Scaledout LSL |
| 1131 |
ScaledoutTrim units |
| 1132 |
trimPointCode |
| 1133 |
enggUnit collection |
| 1134 |
Electronic Temp |
| 1135 |
Electronic temperature value |
| 1136 |
Electronic Temperature Upper Sensor Limit |
| 1137 |
Elecctronic Temperature Lower Sensor Limit |
| 1138 |
Electronic Temp Span |
| 1139 |
Electronic Temperature display unit |
| 1140 |
Electronic Temp Unit |
| 1141 |
Electronic Temperature value damping |
| 1142 |
Electronic Temp Damping |
| 1143 |
Harvester unit |
| 1144 |
Dämpfung eines unruhigen Signals |
| 1145 |
pdpTrimValue units |
| 1146 |
Kalibrieren Druck |
| 1147 |
Pdp trim USL |
| 1148 |
Pdp trim LSL |
| 1149 |
pdp Trimming units |
| 1150 |
upload to device |
| 1151 |
upload from device |
| 1152 |
Common Tables |
| 1153 |
Interoperable * |
| 1154 |
Universal |
| 1155 |
Common Practice |
| 1156 |
Pressure Universal |
| 1157 |
Pressure Common |
| 1158 |
Menu |
| 1159 |
Rosemount Magflow |
| 1160 |
Rosemount Pressure |
| 1161 |
Moore Products |
| 1162 |
Siemens Pressure |
| 1163 |
P2 Common |
| 1164 |
PV |
| 1165 |
Wireless |
| 1166 |
Munge |
| 1167 |
Analytical Oxygen/Combustion/Methane/CO |
| 1168 |
Flow Totalizer - Rate Indicator |
| 1169 |
Flow Variable Area |
| 1170 |
Flow Coriolis Mass |
| 1171 |
Flow Ultrasonic - Gas |
| 1172 |
Flow Ultrasonic - Liquid |
| 1173 |
Level Ultrasonic |
| 1174 |
Level Radar - Microwave |
| 1175 |
Pressure Absolute |
| 1176 |
Level Capacitance |
| 1177 |
Pressure Differential |
| 1178 |
Level Hydrostatic |
| 1179 |
Level |
| 1180 |
Pressure Absolute/Relative |
| 1181 |
Level Microwave |
| 1182 |
Level Radar |
| 1183 |
Level Density - Nuclear |
| 1184 |
Pressure Deltabar S Evolution |
| 1185 |
Pressure Cerabar S Evolution |
| 1186 |
Pressure Deltapilot S Evolution |
| 1187 |
Flow Electromagnetic |
| 1188 |
Flow Vortex |
| 1189 |
Flow Magmeter - Rack Version |
| 1190 |
Flow High Performance Magmeter |
| 1191 |
Flow Mass |
| 1192 |
Flow Ultrasonic |
| 1193 |
Flow Magnetic |
| 1194 |
Flow Magnetic - Custody Transfer |
| 1195 |
Flow 2-wire Magnetic |
| 1196 |
Flow Coriolis Mass - Custody Transfer |
| 1197 |
Flow 2-wire Vortex |
| 1198 |
Flow Thermal |
| 1199 |
Temperature Head Mounted |
| 1200 |
Temperature Compact |
| 1201 |
Temperature DIN Rail Mounted |
| 1202 |
Analytical pH |
| 1203 |
Analytical Conductivity - Conductive |
| 1204 |
Analytical Conductivity - Inductive |
| 1205 |
Temperature Sensor |
| 1206 |
Level Servo |
| 1207 |
Temperature DIN Rail |
| 1208 |
Temperature |
| 1209 |
Analytical ORP |
| 1210 |
Analytical pION |
| 1211 |
Analytical IConc |
| 1212 |
Analytical Electrode Conductivity |
| 1213 |
Analytical Toroidal Conductivity |
| 1214 |
Valve Positioner |
| 1215 |
Valve Controller |
| 1216 |
Pressure |
| 1217 |
Pressure Multivariable |
| 1218 |
Analytical pH/ORP |
| 1219 |
Flow Coriolis |
| 1220 |
Analytical Conductivity |
| 1221 |
Valve Positioner/Pneumatic |
| 1222 |
Valve Actuator - Electrical |
| 1223 |
Temperature Dual Input |
| 1224 |
Valve Actuator |
| 1225 |
Analytical Corrosion |
| 1226 |
Analytical Density - Nuclear |
| 1227 |
Level Continuous Gamma |
| 1228 |
Level Laser Ranging |
| 1229 |
Pressure Safety |
| 1230 |
Flow Vortex/Swirl |
| 1231 |
Flow |
| 1232 |
Analytical 4 Electrode Conductivity |
| 1233 |
Analytical 2 Electrode Conductivity |
| 1234 |
Analytical Troidal Conductivity |
| 1235 |
Analytical pH/ORP/pIon/Ion Conc |
| 1236 |
Analytical Oxygen |
| 1237 |
Pressure P, dP + Multivariable |
| 1238 |
Temperature 2-wire |
| 1239 |
Pressure w/ PID |
| 1240 |
Pressure Saturated Steam |
| 1241 |
Analytical Density - Gamma Ray |
| 1242 |
Level Gamma Ray |
| 1243 |
Analytical Weight - Gamma Ray |
| 1244 |
Level w/ Density - Gamma Ray |
| 1245 |
Analytical Motorized Density |
| 1246 |
Flow Multivariable Mass |
| 1247 |
Temperature Multivariable |
| 1248 |
Specialty HART-to-Analog Signal Conv |
| 1249 |
Flow dP |
| 1250 |
Pressure Low Power |
| 1251 |
Pressure Certified SIL2 |
| 1252 |
Interoperable |
| 1253 |
Analytical Density |
| 1254 |
Valve Positioner/Electropneumatic |
| 1255 |
Flow Magnetic Inductive |
| 1256 |
Analytical |
| 1257 |
Analytical Opacity Monitor |
| 1258 |
Analytical Oxygen/Combustion |
| 1259 |
Analytical 2-wire Conductivity |
| 1260 |
Analytical 2-wire Conductivity w/ pure H20 |
| 1261 |
Analytical 2-wire Conductivity w/ % conc |
| 1262 |
Analytical 2-wire Oxygen/Chlorine/Ozone |
| 1263 |
Analytical 2-wire pH/ORP |
| 1264 |
Analytical 2-wire Contacting/Toroidal |
| 1265 |
Analytical Oxygen - High Temperature |
| 1266 |
Analytical Conductivity w/ % conc |
| 1267 |
Analytical pH/ORP/ISE |
| 1268 |
Analytical Amperometric Analyzer |
| 1269 |
Analytical Dual Input Analyzer |
| 1270 |
Pressure Pressure/Level |
| 1271 |
Analytical Consistency |
| 1272 |
Analytical Microwave-Pulp Consistency |
| 1273 |
Analytical Microwave Consistency |
| 1274 |
Valve Digital Positioner |
| 1275 |
Valve Smart Valve Positioner |
| 1276 |
Temperature Differential |
| 1277 |
Analytical Dissolved Oxygen |
| 1278 |
Analytical pH Controller |
| 1279 |
Analytical Conductivity/Resistivity Controller |
| 1280 |
Analytical Conductivity/Resistivity |
| 1281 |
Level Displacement |
| 1282 |
Temperature w/ PID |
| 1283 |
Valve Universal Positioner |
| 1284 |
Level Radar - Reflex |
| 1285 |
Pressure Gauge |
| 1286 |
Pressure Sealed Gauge |
| 1287 |
Valve Digital Positioner w/ PID |
| 1288 |
Valve Intelligent Positioner |
| 1289 |
Analytical Gas Detector |
| 1290 |
Analytical Infrared Gas Detector |
| 1291 |
Analytical Electrochemical Gas Detector |
| 1292 |
Analytical Measuring Instruments |
| 1293 |
Level Magnostrictive |
| 1294 |
Valve On/Off Valve Controller |
| 1295 |
Level Radar - Pulse |
| 1296 |
Level Continuous Capactive |
| 1297 |
Valve Damper Actuator |
| 1298 |
Valve Electric Damper Actuator |
| 1299 |
Flow Electronic |
| 1300 |
Flow Vortex - Multiparameter Mass |
| 1301 |
Analytical UV Flame Detector |
| 1302 |
Analytical UVIR Flame Detector |
| 1303 |
Analytical IR Flame Detector |
| 1304 |
Analytical Fire Detector |
| 1305 |
Analytical Gas Detector Display Interface |
| 1306 |
Analytical Toxic Gas Detector |
| 1307 |
Analytical Flame Detector |
| 1308 |
Level Nuclear |
| 1309 |
Analytical Microwave |
| 1310 |
Analytical Density - Radiometric |
| 1311 |
Level Radiometric |
| 1312 |
Analytical Gas/Steam |
| 1313 |
Level Nucleonic |
| 1314 |
Analytical Blade Consistency |
| 1315 |
Analytical Rotary Consistency |
| 1316 |
Pressure Absolute/Differential |
| 1317 |
Positioner |
| 1318 |
Analytical Combustible Gas Detector |
| 1319 |
Analytical Point Infrared Gas Detector |
| 1320 |
Analytical Multi-Detector Monitor System |
| 1321 |
Valve Positioner/Electro-hydraulic |
| 1322 |
Valve Monitor |
| 1323 |
Enable on token-passing data link layer only |
| 1324 |
Enable on TDMA data link layer only |
| 1325 |
Enable on both TDMA and token-passing data link layer |
| 1326 |
WirelessHART Device |
| 1327 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 1328 |
Primary |
| 1329 |
Primary Analog Channel |
| 1330 |
Secondary |
| 1331 |
Secondary Analog Channel |
| 1332 |
Tertiary |
| 1333 |
Tertiary Analog Channel |
| 1334 |
Quaternary |
| 1335 |
Quaternary Analog Channel |
| 1336 |
Quinary |
| 1337 |
Quinary Analog Channel |
| 1338 |
Critical Power Failure |
| 1339 |
Lock all |
| 1340 |
Trim not supported |
| 1341 |
Configuration cannot be changed |
| 1342 |
Locked by gateway |
| 1343 |
Analog Input Channel |
| 1344 |
Analog Output Channel |
| 1345 |
Secondary Analog Channel Saturated |
| 1346 |
Tertiary Analog Channel Saturated |
| 1347 |
Quaternary Analog Channel Saturated |
| 1348 |
Quinary Analog Channel Saturated |
| 1349 |
Secondary Analog Channel Fixed |
| 1350 |
Tertiary Analog Channel Fixed |
| 1351 |
Quaternary Analog Channel Fixed |
| 1352 |
Quinary Analog Channel Fixed |
| 1353 |
Simulation active |
| 1354 |
The device is in simulation mode and the level output is not representative of the process. |
| 1355 |
Non-Volatile memory failure |
| 1356 |
The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed. |
| 1357 |
Volatile memory error |
| 1358 |
The RAM memory check is invalid or maybe corrupt |
| 1359 |
Watchdog reset executed |
| 1360 |
A watchdog reset has been performed |
| 1361 |
Voltage conditions out of range |
| 1362 |
A voltage condition is outside its allowable range |
| 1363 |
Environmental conditions out of range |
| 1364 |
An internal or environmental condition is beyond acceptable limits. |
| 1365 |
Electronic failure |
| 1366 |
A hardware problem not related to the sensor has been detected. |
| 1367 |
Subdevice list changed |
| 1368 |
Duplicate master detected |
| 1369 |
Capacity Denied |
| 1370 |
The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified |
| 1371 |
Bandwidth allocation pending |
| 1372 |
Block transfer pending |
| 1373 |
Continuous |
| 1374 |
The Burst Message is published continuously at (worst case) the Minimum Update Period. |
| 1375 |
Window |
| 1376 |
The Burst Message is triggered when the source value deviates more than the specified trigger value |
| 1377 |
Rising |
| 1378 |
The Burst Message is triggered when source value Rises Above the specified trigger value. |
| 1379 |
Falling |
| 1380 |
The Burst Message is triggered when the source value Falls Below the specified trigger value. |
| 1381 |
On-change |
| 1382 |
The Burst Message is triggered when any value in the message changes. |
| 1383 |
Battery life |
| 1384 |
Percent range |
| 1385 |
Loop current |
| 1386 |
Primary variable |
| 1387 |
Secondary variable |
| 1388 |
Tertiary variable |
| 1389 |
Quaternary variable |
| 1390 |
Enable event notification on token-passing data link layer |
| 1391 |
Enable event notification on TDMA data link layer |
| 1392 |
Enable event notification on TDMA and token-passing data link layer |
| 1393 |
Configuration changed event pending |
| 1394 |
Device status event pending |
| 1395 |
More status available event pending |
| 1396 |
Enable single data point trending |
| 1397 |
Enable filtered trending |
| 1398 |
The sample is filtered using a time constant equal to one-third the trend sample period |
| 1399 |
Enable average trending |
| 1400 |
The value obtained by dividing the sum of all samples in the period by the total number of samples |
| 1401 |
Read receive time |
| 1402 |
Write date and time |
| 1403 |
Non-Volatile Clock |
| 1404 |
When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure. |
| 1405 |
Clock Uninitialized |
| 1406 |
The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device. |
| 1407 |
Line Power |
| 1408 |
Device is powered via a hardwired connection to a plant power source. |
| 1409 |
Battery Power |
| 1410 |
Device operates solely of its (internal) battery. |
| 1411 |
Recharg.B./Power Sc. |
| 1412 |
Rechargeable battery power or power scavenging. The device has a short-term supply of energy (must be at least one hour) that is continuously being replenished. The device's power is being replenished by harvesting and converting energy from the environment surrounding the device (e.g. solar, vibration, heat). |
| 1413 |
Idle |
| 1414 |
Active search |
| 1415 |
Looking for neighbors. |
| 1416 |
Negotiating |
| 1417 |
Quarantined |
| 1418 |
Operational |
| 1419 |
Suspended |
| 1420 |
Deep sleep |
| 1421 |
Ultra-low power |
| 1422 |
Wireless Signal Identified |
| 1423 |
Wireless Time Synchronized |
| 1424 |
WirelessHart Signal Identified |
| 1425 |
Network Admission Requested |
| 1426 |
Network Security Clearance Granted |
| 1427 |
Network Bandwidth Requested |
| 1428 |
No restrictions |
| 1429 |
SI Only |
| 1430 |
Restricted to SI Unit codes only |
| 1431 |
Open - accept all devices |
| 1432 |
Use Whitelist for access |
| 1433 |
Use Blacklist |
| 1434 |
Use Whitelist and Blacklist |
| 1435 |
Lockdown - disable join links |
| 1436 |
Process automation device |
| 1437 |
Discrete device |
| 1438 |
Hybrid:Process automation+discrete |
| 1439 |
I/O System |
| 1440 |
WirelessHART Process automation device |
| 1441 |
WirelessHART Discrete device |
| 1442 |
WirelessHART Process automation+discrete |
| 1443 |
WirelessHART Gateway |
| 1444 |
WirelessHART Access point |
| 1445 |
WirelessHART Process adapter |
| 1446 |
WirelessHART Discrete adapter |
| 1447 |
WirelessHART enabled handheld/portable maintenance tool |
| 1448 |
Don't attempt to join |
| 1449 |
Join now |
| 1450 |
Attempt to join immediately on powerup or reset |
| 1451 |
US |
| 1452 |
United States of America |
| 1453 |
JP |
| 1454 |
Japan |
| 1455 |
DE |
| 1456 |
Germany |
| 1457 |
FR |
| 1458 |
France |
| 1459 |
ES |
| 1460 |
Spain |
| 1461 |
RU |
| 1462 |
Russian Federation |
| 1463 |
CN |
| 1464 |
People's Republic of China |
| 1465 |
Nominal |
| 1466 |
Device Power Status is nominal |
| 1467 |
Low |
| 1468 |
Device Power Status is low |
| 1469 |
Critically Low |
| 1470 |
Device Power Status is critically low |
| 1471 |
Recharging - Low |
| 1472 |
Recharging - High |
| 1473 |
Secondary Master |
| 1474 |
Primary Master |
| 1475 |
PV Analog Channel Saturated |
| 1476 |
PV Analog Channel Fixed |
| 1477 |
Device Profile |
| 1478 |
Device Diagnostic Status 0 |
| 1479 |
Device Diagnostic Status 1 |
| 1480 |
I/O and Subdevice Status |
| 1481 |
WirelessHART Status |
| 1482 |
Time Set Option |
| 1483 |
Real Time Clock Flags |
| 1484 |
Country |
| 1485 |
Country of intended device installation |
| 1486 |
SI Unit Control |
| 1487 |
Indicates if device should only display SI unit codes |
| 1488 |
Wired HART Enabled |
| 1489 |
Enabled on Wired HART device connection only |
| 1490 |
Both Wired and WirelessHart Enabled |
| 1491 |
Enabled on both Wired and WirelessHART connections |
| 1492 |
Event Status |
| 1493 |
Event Notification Control |
| 1494 |
Operate mode Mask |
| 1495 |
Not Defined |
| 1496 |
Power Source |
| 1497 |
Power source of the device |
| 1498 |
Wireless Mode |
| 1499 |
Join Status |
| 1500 |
The current location in the joining sequence of operations. |
| 1501 |
Network Access Mode |
| 1502 |
Join Mode |
| 1503 |
Power Status |
| 1504 |
Power status of the device |
| 1505 |
Master Mode |
| 1506 |
This sets the I/O System's Data Link Layer operation on all channels as either primary or secondary master mode. |
| 1507 |
Trend Units |
| 1508 |
Trend Device Variable Unit Code |
| 1509 |
Trend Classification |
| 1510 |
Trend Device Variable Classification |
| 1511 |
Trend Control |
| 1512 |
Device Status Mask |
| 1513 |
Ext dev status Mask |
| 1514 |
Device Diagnostic Status 0 Mask |
| 1515 |
Device Diagnostic Status 1 Mask |
| 1516 |
Device Diagnostic Status 2 Mask |
| 1517 |
Device Diagnostic Status 3 Mask |
| 1518 |
AO saturated Mask |
| 1519 |
AO fixed Mask |
| 1520 |
Latched Device Status |
| 1521 |
Latched Ext dev status |
| 1522 |
Latched Operate Mode |
| 1523 |
Latched Device Diagnostic Status 0 |
| 1524 |
Latched Device Diagnostic Status 1 |
| 1525 |
Latched Device Diagnostic Status 2 |
| 1526 |
Latched Device Diagnostic Status 3 |
| 1527 |
Latched AO saturated |
| 1528 |
Latched AO fixed |
| 1529 |
Wireless Module Device Type |
| 1530 |
Device type of the Wireless Radio |
| 1531 |
Wireless Module Manufacturer ID |
| 1532 |
Manufacturer of the Wireless Radio contained in this device |
| 1533 |
Subdevice Device Type |
| 1534 |
Device type of the subdevice attached to this system. |
| 1535 |
Subdevice Manufacturer Id |
| 1536 |
Manufacturer of the subdevice attached to this system. |
| 1537 |
Time Stamp |
| 1538 |
Relative time value on network |
| 1539 |
8u |
| 1540 |
Dynamic Variables Returned for Device Variables |
| 1541 |
Command Response Truncated |
| 1542 |
Configuration Change Counter Mismatch |
| 1543 |
Status bytes mismatch |
| 1544 |
Device Variable |
| 1545 |
Total Burst Msgs |
| 1546 |
Total number of burst messages supported by this device |
| 1547 |
Burst Variable Code |
| 1548 |
Update Period |
| 1549 |
Burst Message Number |
| 1550 |
Variable to trim |
| 1551 |
Update time adjusted |
| 1552 |
Burst condition conflict |
| 1553 |
Update period increased |
| 1554 |
Insufficient bandwidth |
| 1555 |
8.3f |
| 1556 |
Aborting procedure due to last error |
| 1557 |
Now Apply input pressure
URV:%[8.3f]{upperRange_value} %{pdp_units} LRV:%[8.3f]{lowerRange_value} %{pdp_units} |
| 1558 |
Current process value: %[8.3f]{pdp_value}
%{pdp_units} |
| 1559 |
Continue read value;Set as lower range value;Set as upper range value;Exit |
| 1560 |
URV:%[8.3f]{upperRange_value} %{pdp_units}
LRV:%[8.3f]{lowerRange_value} %{pdp_units} |
| 1561 |
PV value read
PV : %[8.3f]{pdp_value}%{pdp_units} |
| 1562 |
Set PV Zero;Ready |
| 1563 |
PV value read
PV: %[8.3f]{pdp_value}%{pdp_units} |
| 1564 |
Set PV Value;Ready |
| 1565 |
Enter new PV value: |
| 1566 |
P-dP Bias will be Reset |
| 1567 |
OP :%[5.2f]{percentRange}% PV :%[8.3f]{pdp_value}%{pdp_units}
URV and LRV will be shifted. Continue? |
| 1568 |
Yes;No |
| 1569 |
Enter new OP percent val: |
| 1570 |
Last Input val used:
Hival: %[8.3f]{pdpSensor_hitrim}%{pdpSensor_trimunits}
Loval: %[8.3f]{pdpSensor_lotrim}%{pdpSensor_trimunits} |
| 1571 |
Select choice: |
| 1572 |
High Trim;Low Trim;Display limits;Exit |
| 1573 |
Apply a Hival Pres. Higher than Loval |
| 1574 |
Pressure stabilizing. PLEASE WAIT... |
| 1575 |
Last used Hival: %[8.3f]{pdpSensor_hitrim}%{pdpSensor_trimunits}
Enter applied Hival: |
| 1576 |
Apply a Loval Pres. Lower than Hival |
| 1577 |
Last used Loval: %[8.3f]{pdpSensor_lotrim}%{pdpSensor_trimunits}
Enter applied Loval: |
| 1578 |
SENSOR LIMITS:
USL: %[8.3f]{pdp_USL}%{pdp_units}
LSL: %[8.3f]{pdp_LSL}%{pdp_units} |
| 1579 |
Last Input val used:%[8.3f]{st_lotrim}%{stTrimValue_units} |
| 1580 |
Last Input val used: %[8.3f]{st_lotrim}%{stTrimValue_units}
Enter the reference Temperature: |
| 1581 |
Applied values read:
PV: %{pdpTrimValue} %{pdpTrimValue_units} |
| 1582 |
Applied zero reads:
PV: %[8.3f]{pdpTrimValue}%{pdpTrimValue_units} |
| 1583 |
Do you want to retry? |
| 1584 |
YES;NO |
| 1585 |
Applied values read:
PV: %[8.3f]{staticpr_Value} %{staticPressure_units} |
| 1586 |
Applied zero reads:
PV: %[8.3f]{staticpr_Value}%{staticPressure_units} |
| 1587 |
Last Input Loval used: %[8.3f]{staticPressureSensor_lotrim}%{staticPressureTrimValue_units} |
| 1588 |
Apply Pressure |
| 1589 |
Last Loval used: %[8.3f]{staticPressureSensor_lotrim}%{staticPressureTrimValue_units}
Enter applied Loval: |
| 1590 |
The Sensor Trimming is set to the User trimming! Actual settings are lost. Continue? |
| 1591 |
The Configuration Changed Flag is cleared! Continue? |
| 1592 |
The Actual Sensor Trimming is Saved as User Trimming! Continue? |
| 1593 |
The Sensor Trimming parameters are set to the factory settings! User specific settings are lost. Continue? |
| 1594 |
Hardware Version:0%{hardwareRevision_byte0}.0%{hardwareRevision_byte1}.0%{hardwareRevision_byte2} |
| 1595 |
Software Version:0%{softwareRevision_byte0}.0%{softwareRevision_byte1}.0%{softwareRevision_byte2} |
| 1596 |
Messwerksrevision:0%{sensorRevision_byte0}.0%{sensorRevision_byte1}.0%{sensorRevision_byte2} |
| 1597 |
P-dP Simulation aktiv |
| 1598 |
Scaled Output Simulation Active |
| 1599 |
P-dP Simulation aktiv
Statische Drucksimulation aktiv |
| 1600 |
P-dP Simulation aktiv
Messwerk-Temperatursimulation aktiv |
| 1601 |
P-dp Simulation Active
Scaled Output Simulation Active |
| 1602 |
Statische Drucksimulation aktiv
Messwerk-Temperatursimulation aktiv |
| 1603 |
Static Pressure Simulation Active
Scaled Output Simulation Active |
| 1604 |
Sensor Temperature Simulation Active
Scaled Output Simulation Active |
| 1605 |
P-dP Simulation aktiv
Statische Drucksimulation aktiv
Messwerk-Temperatursimulation aktiv |
| 1606 |
P-dp Simulation Active
Static Pressure Simulation Active
Scaled Output Simulation Active |
| 1607 |
P-dp Simulation Active
Sensor Temperature Simulation Active
Scaled Output Simulation Active |
| 1608 |
Static Pressure Simulation Active
Sensor Temperature Simulation Active
Scaled Output Simulation Active |
| 1609 |
P-dp Simulation Active
Static Pressure Simulation Active
Sensor Temperature Simulation Active
Scaled Output Simulation Active |
| 1610 |
Primärvariable unterhalb des Messanfangs |
| 1611 |
Primärvariable oberhalb des Messende |
| 1612 |
Primärvariable unterhalb des Messanfangs
Primärvariable oberhalb des Messende |
| 1613 |
Tage :%{totalWorkingTime_day}
Stunden :%{hours}
Minuten :%{min}
Sekunden :%{sec} |
| 1614 |
SV is: |
| 1615 |
TV is: |
| 1616 |
QV is: |
| 1617 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}000000000%{Local_DeviceSerialNumber} |
| 1618 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}00000000%{Local_DeviceSerialNumber} |
| 1619 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}0000000%{Local_DeviceSerialNumber} |
| 1620 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}000000%{Local_DeviceSerialNumber} |
| 1621 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}00000%{Local_DeviceSerialNumber} |
| 1622 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}0000%{Local_DeviceSerialNumber} |
| 1623 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}000%{Local_DeviceSerialNumber} |
| 1624 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}00%{Local_DeviceSerialNumber} |
| 1625 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}0%{Local_DeviceSerialNumber} |
| 1626 |
Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}%{Local_DeviceSerialNumber} |
| 1627 |
Sensor Serial No:%{serialNo_Part4}%{serialNo_Part5}%{serialNo_Part6}%{serialNo_Part7}%{serialNo_Part8} |
| 1628 |
Please select |
| 1629 |
Simulate P-dP;Simulate Sensor Temperature;Simulate scaled out;Exit Simulation |
| 1630 |
P-dP value read %[.2f]{pdp_value}%{pdp_units} |
| 1631 |
Continue;Back |
| 1632 |
Enter simulation value |
| 1633 |
Sensor Temperature value read %[.2f]{sensorTemperature_value}%{sensorTemperature_units} |
| 1634 |
Scaled out value read %[.2f]{communicationScaleOutValue}%{communicationScaleOutValue_units} |
| 1635 |
Simulate P-dP;Simulate Static Pressure;Simulate Sensor Temperature;Simulate scaled out;Exit Simulation |
| 1636 |
Static pressure value read %[.2f]{staticpr_Value}%{staticPressure_units} |
| 1637 |
Squawk started
Select OK to Stop |
| 1638 |
Setting fld dev output to 1Vdc |
| 1639 |
Setting fld dev output to 5Vdc |
| 1640 |
Choose Voltage Output Level |
| 1641 |
1Vdc;5Vdc;Other;End |
| 1642 |
Fld dev output is fixed at %0 Vdc |
| 1643 |
The Output Trimming parameters are set to the factory settings! User specific settings are lost. Continue? |