Device dictionary

Loading…

Reference ID	String
0	ABB
1	600T
2	EEPROM 1 error
3	EEPROM 2 error
4	Stat Pres ool
5	Sens Temp ool
6	Elec Temp ool
7	Sensor failed
8	ASIC Counter ool
9	Checksum error
10	Stat Pres oopl
11	Sens Temp oopl
12	Elec Temp oopl
13	Field Device Primary Variable Unit - Engineering unit that the Digital Value, Upper Range Value and Lower Range value will be displayed with.
14	inH2O @20DegC
15	inHg @0DegC
16	feet H2O @20DegC
17	mmH2O @20DegC
18	mmHg @0DegC
19	torr @0DegC
20	Up-Down Scale mode - Defines the setting of the current output when fatal errors are detected.
21	Up-Down Scale mode
22	Transfer Function - Defines the transformation function that will be applied between the Field Device Variable and the respective assigned Analog Output. The transfer function does not affect the Digital Value.
23	5th Order polyn
24	Meter Installation - Defines whether there is a meter installed or not and, if integral, what information the meter will display.
25	Analog - 4-20mA
26	Digital - 4-20mA
27	Integral digital
28	Push Buttons - Indicates whether the instrument is fitted with Zero and/or Span calibration buttons.
29	Push Buttons
30	No Push Buttons
31	Zero Pushbutton only
32	Zero & Span Pushbut.
33	Flange Type - Hardware, adjacent to the sensor, that physically connects the process to the sensor.
34	1/2in NPT-F
35	DIN
36	Conventl. + insert
37	Flange Material - Indicates the material of the flange.
38	17-4-PH
39	316L + PTFE insert
40	Oring Material - Indicates the construction material of a seal that exists between the module and the flange.
41	TFE Glass filled
42	Drain Vent Material - Indicates the material of the vents.
43	AISI 303 SS
44	AISI 316L SS NACE
45	Remote Seal Isolator Material - Defines the material of the remote seal wetted diaphragm.
46	Hastelloy C276
47	AISI 316L TFE Coated
48	Nickel
49	Zirconium
50	Silver
51	Module Isolator Material - Indicates the material of the sensor diaphragm.
52	Remote Seal Type - Defines the type of Remote seal.
53	Threaded
54	Chemical Tee
55	Button
56	Tri Clamp
57	Threaded food
58	Union Connection
59	Remote Seal Fill Fluid - Defines the remote seal filling liquid.
60	Santotherm
61	Silicon oil food
62	Neobee
63	Dowtherm
64	Ethyl benzene
65	Ethyl alcohol
66	Propylene glycol/Water
67	Dibutyl penthalate
68	Siltherm 800
69	Number of Remote Seals - Physical quantity of the seals for the remote seal that is installed.
70	Sensor Fill Fluid - Fluid material in the module.
71	Module range - This is the range for the sensor.
72	2.5 kpa
73	5 kpa
74	7.5 kpa
75	10 kpa
76	12.5 kpa
77	15 kpa
78	25 kpa
79	40 kpa
80	50 kpa
81	60 kpa
82	80 kpa
83	120 kpa
84	140 kpa
85	160 kpa
86	200 kpa
87	250 kpa
88	400 kpa
89	600 kpa
90	1200 kpa
91	1600 kpa
92	2400 kpa
93	3200 kpa
94	4200 kpa
95	4800 kpa
96	6000 kpa
97	25 mbar
98	50 mbar
99	75 mbar
100	100 mbar
101	125 mbar
102	150 mbar
103	250 mbar
104	400 mbar
105	500 mbar
106	600 mbar
107	800 mbar
108	1200 mbar
109	1400 mbar
110	1600 mbar
111	2000 mbar
112	2500 mbar
113	4000 mbar
114	6000 mbar
115	12000 mbar
116	16000 mbar
117	24000 mbar
118	32000 mbar
119	42000 mbar
120	48000 mbar
121	60000 mbar
122	10 mpa
123	12 mpa
124	16 mpa
125	25 mpa
126	32 mpa
127	40 mpa
128	60 mpa
129	80 mpa
130	100 mpa
131	10 inH2O
132	20 inH2O
133	30 inH2O
134	40 inH2O
135	50 inH2O
136	60 inH2O
137	100 inH2O
138	160 inH2O
139	200 inH2O
140	240 inH2O
141	320 inH2O
142	480 inH2O
143	560 inH2O
144	640 inH2O
145	800 inH2O
146	46 mmHg
147	37 mmHg
148	56 mmHg
149	75 mmHg
150	93 mmHg
151	112 mmHg
152	187 mmHg
153	300 mmHg
154	375 mmHg
155	450 mmHg
156	600 mmHg
157	900 mmHg
158	1050 mmHg
159	1200 mmHg
160	1500 mmHg
161	58 psia
162	87 psia
163	174 psia
164	232 psia
165	348 psia
166	464 psia
167	609 psia
168	696 psia
169	870 psia
170	58 psig
171	87 psig
172	174 psig
173	232 psig
174	348 psig
175	464 psig
176	609 psig
177	696 psig
178	870 psig
179	1450 psi
180	1740 psi
181	2320 psi
182	3625 psi
183	4641 psi
184	5801 psi
185	8702 psi
186	11603 psi
187	14503 psi
188	Calibration Type - Indicates if std. or specific on operating pressure or temperature or both.
189	Procedure Type - It is the type of any special procedure required for the manufacture of the sensor, e.g. degreasing.
190	Procedure Type
191	Oxygen Cleaning
192	Chlorine Cleaning
193	Hydrogen Preparation
194	Special Degreasing
195	Local keys mode control - Disables the Zero and Span Push buttons.
196	Local keys mode
197	LCD display mode control - Selects the variables shown on the integral display.
198	LCD display mode
199	Process variable
200	PV & % of range
201	PV & oput current
202	% of range
203	Root transfer function mode - selects behaviour of square root output at input values from 0 - 4 %.
204	Root transfer mode
205	Linear 20 % oput
206	Lin 1:1 20 % oput
207	Field Device Primary Variable Value - Represents the input pressure.
208	.3f
209	.2f
210	Sensor Limit Units and Minimum Span Units - Engineering units that the Upper Sensor Limit, Lower Sensor Limit and Minimum Span will be displayed with.
211	Sensor Limits Units
212	Module Type - Defines the Module type of the field instrument.
213	High Static Pressure
214	Special Transfer Function.
215	Special Transfer Function
216	Lower Sensor Trim Point - Applied process pressure at which the last lower sensor trim was performed. Pressure Sensor - Pressure hardware that measures pressure with respect to some reference pressure.
217	Upper Sensor Trim Point - Applied process pressure at which the last upper sensor trim was performed. Pressure Sensor - Pressure hardware that measures pressure with respect to some reference pressure.
218	Sensor trim units - It is the unit of the sensor trim points.
219	Sensor trim units
220	Maximum Working Pressure - Indicates the maximum pressure to which the transmitter can be submitted without causing danger and damage.
221	Maximum Working Pressure Units - The units of the Maximum working pressure.
222	Maximum sensor Pressure - Indicates the maximum temperature to which the sensor or the electronic can be submitted without causing danger and damage.
223	Max sens temp
224	Max sens temp units
225	Maximum sensor temperature units - The units of the Maximum sensor or electronic temperature units.
226	Minimum sensor Temperature - Indicates the minimum temperature to which the sensor or the electronic can be submitted without causing danger and damage.
227	Min sens temp
228	Min sens temp units
229	Minimum sensor temperature units - The units of the Minimum sensor or electronic temperature units.
230	A5 coefficient - A5 coefficient for polynomial function.
231	A5
232	1.6g
233	A4 coefficient - A4 coefficient for polynomial function.
234	A4
235	A3 coefficient - A3 coefficient for polynomial function.
236	A3
237	A2 coefficient - A2 coefficient for polynomial function.
238	A2
239	A1 coefficient - A1 coefficient for polynomial function.
240	A1
241	A0 coefficient - A0 coefficient for polynomial function.
242	A0
243	Analog Output value - Indicates the current output of the field instrument.
244	Analog Output
245	Percent of Range - Digital value that is proportional to the range defined by the Lower Range Value and the Upper Range Value. The units of this variable is always in percent.
246	%
247	Upper Sensor Limit - Value that defines the absolute upper endpoint (largest magnitude) for the digital value. Pressure - Pressure of the process measured with respect to some reference pressure.
248	.1f
249	Lower Sensor Limit - Value that defines the absolute lower endpoint (smallest magnitude) for the digital value. Pressure - Pressure of the process measured with respect to some reference pressure.
250	Upper Range - Defines the operational endpoint from which the Analog Value and the Percent of Range are derived. In addition, the range values define the points at which the 'analog output saturated' warning is set.
251	Lower Range - Defines the operational endpoint from which the Analog Value and the Percent of Range are derived. In addition, the range values define the points at which the 'analog output saturated' warning is set.
252	Damping Value - Damping time constant applied to both the Digital Value and Analog Value of the respective output. The Units of this variable are always in seconds.
253	2.2f
254	5.2f
255	Tertiary variable Static Pressure Value.
256	Static Pres
257	Tertiary variable Static Pressure Units.
258	Sta pres unit
259	Static Pressure trim point - The pressure at which static trim is to take place.
260	Stat Pres trim pt
261	Static Pressure Trim Unit - Units of the static pressure trim point.
262	Stat Pres trim unit
263	MPa
264	Secondary variable Sensor Temperature Value - The displayed temperature is not the process temperature, it is the temperature in the sensor's core.
265	Snsr temp
266	Secondary variable Sensor Temperature Unit.
267	Snsr temp unit
268	Fourth Variable - Temperature of the electronics.
269	Elec temp
270	Fourth Variable Electronic Temperature Unit.
271	Product Code - Specifies the transmitter's code number.
272	Product code
273	Separator &/or Services - Indicates the code of remote seal or code for special services or calibration.
274	Sepratr&/Service
275	Manifold or Orifice - Indicates the code of manifold or integral orifice.
276	Manf or orifice
277	Minimum Span value - Indicates the minimum allowable value for the span. The span is the algebraic difference between the Upper and Lower Range Value.
278	Min span
279	Sensor Serial Number - Indicates the sensor module serial number.
280	7d
281	Up Down Scale Mode
282	This is the array for the dynamic variables
283	Field Device Dynamic variables array
284
285	Excess Correction Attempted
286	Configure
287	Zero/Span cal
288	Status
289	Pres sensor trim
290	Sensor trim points
291	Sensor
292	Pres sensor
293	Pres sensor info
294	Temp sensor
295	Stat sensor
296	Pres input scaling
297	Display Limits
298	Product codes
299	Material Info
300	Revision #'s
301	Misc Info
302	write_variables
303	Offline
304	Back to normal
305	Back to normal with msg
306	Factory trim
307	Factory trim method - The factory trimming is a reset to the values used in the factory for the trimming operation and can be usually done without the need of external equipment.
308	Full trim method - The full trimming allows the performance of high or low trim.
309	Full trim
310	Static trim method - The static trimming allows a single point trim of Static Pressure
311	Static trim
312	Rerange 4-20mA
313	Perform a device rerange to 4 - 20ma by applying source pressure input.
314	Put coef0 into range 0-100
315	Put coef2 into range 0-100
316	Put coef3 into range 0-100
317	Put coef4 into range 0-100
318	Put coef5 into range 0-100
319	Put coef0 into range 0-1
320	Put coef2 into range 0-1
321	Put coef3 into range 0-1
322	Put coef4 into range 0-1
323	Put coef5 into range 0-1
324	Danger for max working pressure
325	Loop in manual
326	Before polling
327	Commands the DPK pressure electronics to perform a selftest.
328	Polyn. coeffs
329	FMU860
330	DT
331	DVC
332	FCX
333	AS800
334	340T
335	340C
336	344
337	Siemens Micro K
338	SITRANS L
339	SIPAN PH
340	SITRANS P
341	75SMT
342	UNIDELTA
343	8320
344	SX5100
345	TSV175
346	DMU
347	3780
348	BM70
349	8u
350	low
351	high
352	Field Device Variable Unit- Engineering unit to be displayed with the Digital Value representation, Minimum Span, Upper Range Value, Lower Range Value, Lower Sensor Limit, and Upper Sensor Limit. Pressure- Pressure of the process measured with respect to a reference pressure.
353	Send warning
354	Send Warning- Yields a units code notice to the User.
355	Variables which use this as the units code will be in the previous units until this value is sent to the device.
356	Note: Loop may be returned to automatic control when SEND is done
357	If transfer function changed chech square root mode & poly coeffs.
358	Trim will be set as at factory
359	Applied values read: PV: %{1} Units: %{0}
360	Applied zero reads: PV: %{1} Units: %{0}
361	Last Input val used: Units: %{0} Hival: %{2} Loval: %{1}
362	Select choice:
363	High Trim;Low Trim;Display limits;Exit
364	Apply a Hival Pres. Higher than Loval
365	Pressure stabilizing. PLEASE WAIT...
366	Units: %{0} Pres. applied: %{1}
367	Enter applied Hival:
368	Aborting procedure due to last error
369	Apply a Loval Pres. Lower than Hival
370	Enter applied Loval:
371	SENSOR LIMITS: Units:%{0} USL: %{2} LSL: %{1}
372	Static value read stat value: %{0} units: %{1}
373	Modify;Ready
374	Enter static value:
375	Now Apply input pressure (URV is %{0}) (LRV is %{1})
376	Current process value: %{0} %{1}
377	Read new value;Set as 4mA value;Set as 20mA value;Exit
378	DANGER: Change of this value affects plant and personnel safety. MUST be done by qualified personnel only.
379	WARN: TX with polling address different from 0 cannot be part of a control loop.
380	Executing selftest. PLEASE WAIT...
381	Self test terminated
Reference ID	String