Device dictionary

Loading…

Reference ID	String
0	ATT2200
1	Autrol(Duon)
2	Duon System
3	Failure
4	Out of Specification
5	Function Check
6	Device Variable Simulation Active
7	The device is in simulation mode and one or more of its device variables are not representative of the process.
8	Non-Volatile Memory Defect
9	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
10	Volatile Memory Defect
11	The RAM memory check is invalid or maybe corrupt
12	Watchdog Reset Executed
13	A watchdog reset has been performed
14	Power Supply Conditions Out of Range
15	The power source, supply or voltage is outside its allowable range.
16	Environmental Conditions Out of Range
17	An internal or environmental condition is beyond acceptable limits.
18	Electronic Defect
19	A hardware problem not related to the sensor has been detected.
20	Device Configuration Locked
21	Device is in write-protect or is locked
22	External EEPROM write fail
23	Oscillator Fault
24	Sensor Input open error
25	RTD 3 wire open error
26	RTD 4 wire open error
27	ADC Setting error
28	ADC Counter over limit
29	ADC read time out
30	Sensor code error
31	Analog checksum fail
32	Flash memory write fail
33	Flash Access violation
34	Flash checksum fail
35	Primary Value
36	.3f
37	Snsr PV unit
38	Sensor Temperature Units
39	PV Family
40	PV Class
41	PV PDQ
42	PV LS
43	PV Fmly stat
44	PV USL
45	PV LSL
46	PV min span
47	PV damp
48	8.3f
49	PV Update Period
50
51	s
52	PV snsr s/n
53	7d
54	PV Lower trim
55	PV Upper trim
56	PV Trim support
57	PV Min lower trim
58	PV Max lower trim
59	PV Min upper trim
60	PV Max upper trim
61	PV Min trim diff
62	Simulate
63	PV
64	Primary Variable - Temperature
65	Update Period
66	Secondary Value
67	Snsr SV unit
68	SV Family
69	SV Class
70	SV PDQ
71	SV LS
72	SV Dev Stat
73	SV USL
74	SV LSL
75	SV min span
76	SV damp
77	SV Update Period
78	SV snsr s/n
79	SV
80	Secondary Variable - Temperature
81	Device transmitter variable code
82	Xmtr Variable
83	Pri-Var
84	Sec-Var
85	Tri-Var
86	4th-Var
87	Temperature Tranmitter Sensor Type Code
88	Selected Sensor Type
89	mV
90	Ohms
91	T/C-B Type
92	T/C-E Type
93	T/C-J Type
94	T/C-K Type
95	T/C-N Type
96	T/C-R Type
97	T/C-S Type
98	T/C-T Type
99	T/C-B CJ Only
100	T/C-E CJ Only
101	T/C-J CJ Only
102	T/C-K CJ Only
103	T/C-N CJ Only
104	T/C-R CJ Only
105	T/C-S CJ Only
106	T/C-T CJ Only
107	T/C-B CJ Off
108	T/C-E CJ Off
109	T/C-J CJ Off
110	T/C-K CJ Off
111	T/C-N CJ Off
112	T/C-R CJ Off
113	T/C-S CJ Off
114	T/C-T CJ Off
115	PT-100 2W DIN
116	PT-100 3W DIN
117	PT-100 4W DIN
118	PT-100 2W US
119	PT-100 3W US
120	PT-100 4W US
121	PT-100 2W NI
122	PT-100 3W NI
123	PT-100 4W NI
124	Update Failure
125	Invalid Transmitter Variable Code
126	Invalid Sensor Type Code
127	Change current PV to zero adjustmet value
128	Adjust value
129	8.4f
130	Xmtr Unit Code
131	Total Table
132	2d
133	Num Of Item
134	One
135	Two
136	Start Item No
137	Next Item No
138	BasePntVal
139	6.2f
140	NextBasePnt
141	MdfyPntVal
142	NxtMdfyPnt
143	Invalid Alarm Selection Code
144	Performed by Hardware
145	No Write Protected
146	Write Protected
147	Write protect
148	Adjust Trim
149	More Status Clear
150	Sensor Selection
151	Sensor Connection
152	Get Linear Table
153	Autrol.Pressure
154	Device settings
155	Diagnostics
156	Maintenance
157	Offline
158	Temperature sensor
159	Concentration sensor
160	Operate
161	Autrol Setup
162	Dynamic Variables
163	Device Status
164	PV Analog Channel Saturated
165	PV Analog Channel Fixed
166	Wireless
167	WirelessHART Device
168	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
169	Primary
170	Primary Analog Channel
171	Secondary
172	Secondary Analog Channel
173	Tertiary
174	Tertiary Analog Channel
175	Quaternary
176	Quaternary Analog Channel
177	Quinary
178	Quinary Analog Channel
179	Critical Power Failure
180	Lock all
181	Trim not supported
182	Configuration cannot be changed
183	Locked by gateway
184	Analog Input Channel
185	Analog Output Channel
186	Secondary Analog Channel Saturated
187	Tertiary Analog Channel Saturated
188	Quaternary Analog Channel Saturated
189	Quinary Analog Channel Saturated
190	Secondary Analog Channel Fixed
191	Tertiary Analog Channel Fixed
192	Quaternary Analog Channel Fixed
193	Quinary Analog Channel Fixed
194	Simulation active
195	The device is in simulation mode and the level output is not representative of the process.
196	Non-Volatile memory failure
197	Volatile memory error
198	Watchdog reset executed
199	Voltage conditions out of range
200	A voltage condition is outside its allowable range
201	Environmental conditions out of range
202	Electronic failure
203	Subdevice list changed
204	Duplicate master detected
205	Capacity Denied
206	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
207	Bandwidth allocation pending
208	Block transfer pending
209	Battery life
210	Percent range
211	Loop current
212	Primary variable
213	Secondary variable
214	Tertiary variable
215	Quaternary variable
216	Read receive time
217	Write date and time
218	Non-Volatile Clock
219	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
220	Clock Uninitialized
221	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
222	None
223	No restrictions
224	SI Only
225	Restricted to SI Unit codes only
226	Process automation device
227	Discrete device
228	Hybrid:Process automation+discrete
229	I/O System
230	WirelessHART Process automation device
231	WirelessHART Discrete device
232	WirelessHART Process automation+discrete
233	WirelessHART Gateway
234	WirelessHART Access point
235	WirelessHART Process adapter
236	WirelessHART Discrete adapter
237	WirelessHART enabled handheld/portable maintenance tool
238	Device Profile
239	US
240	United States of America
241	JP
242	Japan
243	DE
244	Germany
245	FR
246	France
247	ES
248	Spain
249	RU
250	Russian Federation
251	CN
252	People's Republic of China
253	Secondary Master
254	Primary Master
255	Device Diagnostic Status 0
256	Device Diagnostic Status 1
257	I/O and Subdevice Status
258	WirelessHART Status
259	Time Set Option
260	Real Time Clock Flags
261	Country
262	Country of intended device installation
263	SI Unit Control
264	Indicates if device should only display SI unit codes
265	8u
266	Dynamic Variables Returned for Device Variables
267	Command Response Truncated
268	Configuration Change Counter Mismatch
269	Status bytes mismatch
270	Output Status
271	Output Status Byte
272	Uninitialized
273	Normal - one sensor
274	Normal - two sensors
275	Normal - three sensors
276	Shorted
277	Shorted- shorted field wiring.
278	Limited high
279	Limited high- block can not respond to upward movement of value.
280	Open
281	Open- open field wiring.
282	Limited low
283	Limited low- block can not respond to upward movement of target.
284	Initialization done
285	Initialization done- block initialization is complete.
286	Not selected
287	Not selected- target value provided by block was not selected.
288	No path
289	No path- there is no path to the process.
290	Fail
291	Fail- hardware failure.
292	Bad
293	Bad- block is out of service or has bad input.
294	Not from process
295	Not from process- value is not directly affected by any process information.
296	Local override
297	Local override- block has LO mode.
298	Not Cascade Mode
299	Not RCas Mode
300	Not ROut Mode
301	No communication
302	No communication- (NO_COM).
303	uint16_var_blk_char
304	uint32_var_blk_char
305	uint8_var_blk_char
306	int8_var_blk_char
307	new itest redef1 label
Reference ID	String