Device dictionary

Loading…

Reference ID	String
0	38xxVA
1	Documents the accuracy class of the meter when shipped.
2	AccClass
3	Shows the last-annunciated alarm
4	Alrm:
5	None
6	Diagnostic
7	Diagnostic Alarm
8	DBase Init
9	Database Initialization
10	Power Fail
11	Power Failure
12	Int Temp
13	Internal Puck Temperature
14	Hi Flow
15	Pulse O/P
16	Pls Over
17	Pulse Output Overrun
18	Low Flow
19	Unknown
20	Tracking
21	The Analog Output is tracking the process normally
22	Upscale
23	The Analog Output is forced to maximum
24	Downscale
25	The Analog Output is forces to minimum
26	Hold Last
27	The Analog Output is holding last output value
28	4.1f
29	Units of Measure for Calibration Density
30	CalDens Unit
31	Calibration Flow Rate associated with FloatPosition 1
32	CFlow 1
33	9.2f
34	Calibration Flow Rate associated with FloatPosition 10
35	CFlow 10
36	Calibration Flow Rate associated with FloatPosition 2
37	CFlow 2
38	Calibration Flow Rate associated with FloatPosition 3
39	CFlow 3
40	Calibration Flow Rate associated with FloatPosition 4
41	CFlow 4
42	Calibration Flow Rate associated with FloatPosition 5
43	CFlow 5
44	Calibration Flow Rate associated with FloatPosition 6
45	CFlow 6
46	Calibration Flow Rate associated with FloatPosition 7
47	CFlow 7
48	Calibration Flow Rate associated with FloatPosition 8
49	CFlow 8
50	Calibration Flow Rate associated with FloatPosition 9
51	CFlow 9
52	Units of Measure for Meter Calibration Flow Rates
53	CF Unit
54	L/d
55	Liters per Day
56	g/d
57	Grams per Day
58	Tons/sec
59	Tons per Second
60	MTon/sec
61	Metric Tons per Second
62	Calibration Date
63	CalDate
64	Calibration Density
65	CalDens
66	5.4f
67	5.1f
68	Calibration Factor. Allows for a different process fluid (density/viscosity) than was used for factory calibration
69	CalFact
70	6.4f
71	Calibration Fluid
72	CalFluid
73	Calibration Pressure
74	CalPres
75	6.1f
76	Calibration Temperature
77	CalTemp
78	Calibration Tool
79	CalTool
80	Calibration Viscosity
81	CalVisc
82	Calibrator Name/Initials
83	CalName
84	Units of Measure for Calibration Pressure
85	CalPres Unit
86	Units of Measure for Calibration Temperature
87	CalTemp Unit
88	Units of Measure for Calibration Viscosity
89	CalVisc Unit
90	Selects the Contact Output Function from a list of choices
91	Function
92	None, manually driven output
93	Alarm O/P
94	Alarm contact ouput gate
95	Selects the Polarity of the Contact Output, N.O. or N.C.
96	Polarity
97	N/O
98	Normally Open
99	N/C
100	Normally Closed
101	Displays the active/inactive state of the Contact Output
102	State
103	Off
104	Not On
105	On
106	Not Off
107	Sets how the Field Device will annunciate the alarm.
108	Dest
109	No Alarm Destination
110	Contact O/P1
111	Energize Contact Output1
112	Contact O/P2
113	Both Contacts
114	Energize Both Contacts upon Alarm
115	Enable or Disable this Alarm
116	Enable
117	Disabled
118	Enabled
119	Sets the persistence level of the Alarm, Latching or Non-Latching
120	Type
121	Non Latching
122	Latching
123	Units of Measure for Density parameters
124	Diagnostic Code
125	Diag Code
126	Documents the presence of the External Termination Box
127	Ext Term
128	Documents the material code for the flanges, end-fittings
129	Flange Matl
130	Hastelloy B2
131	Documents the type of flanges, end-fittings
132	Flange Type
133	NPT_Threads
134	MS_Tubing
135	ANSI_150#RF
136	ANSI_300#RF
137	ANSI_400#RF
138	ANSI_600#RF
139	ANSI_900#RF
140	DIN_PN10
141	DIN_PN15
142	DIN_PN25
143	DIN_PN40
144	DIN_PN50
145	DIN_PN64
146	DIN_PN80
147	DIN_PN100
148	DIN_SPUD
149	TRI_CLOVER
150	JIS_10K_RF
151	JIS_16K_RF
152	Documents the material code used in the float
153	Float Matl
154	Shows the present float-position, as a diagnostic indication
155	FltPos
156	7.2f
157	The float position (degrees of angle) associated with Calibration Flow Rate 1
158	Pos01
159	6.2f
160	The float position (degrees of angle) associated with Calibration Flow Rate 10
161	Pos10
162	The float position (degrees of angle) associated with Calibration Flow Rate 2
163	Pos02
164	The float position (degrees of angle) associated with Calibration Flow Rate 3
165	Pos03
166	The float position (degrees of angle) associated with Calibration Flow Rate 4
167	Pos04
168	The float position (degrees of angle) associated with Calibration Flow Rate 5
169	Pos05
170	The float position (degrees of angle) associated with Calibration Flow Rate 6
171	Pos06
172	The float position (degrees of angle) associated with Calibration Flow Rate 7
173	Pos07
174	The float position (degrees of angle) associated with Calibration Flow Rate 8
175	Pos08
176	The float position (degrees of angle) associated with Calibration Flow Rate 9
177	Pos09
178	Documents the type of float used in this meter
179	Float Type
180	Units of Measure for Flow Rate
181	FlowRate Units
182	High Limit
183	Limit
184	Time Period over which flow exceeds limits before an alarm is generated
185	Time
186	Temperature of the electronics inside the transmitter
187	Hi
188	Low Limit
189	Lo
190	Inventory Totalizer
191	InvTot
192	8.0f
193	8.1f
194	8.2f
195	8.3f
196	8.4f
197	8.5f
198	8.6f
199	8.7f
200	Inventory Totalizer Number of Digits and Decimal Digits to Display
201	Dec Digits
202	99999999.
203	9999999.9
204	999999.99
205	99999.999
206	9999.9999
207	999.99999
208	99.999999
209	9.9999999
210	Inventory Totalizer Units of Measure
211	Unit
212	Dl
213	DecaLiters
214	ml
215	MilliLiters
216	cu cm
217	Cubic Centimeters
218	Analog Output Loop Current
219	The lowest flow-rate for this meter, below which the transmitter will indicate zero flow, accumulate no totals, and create no output pulses
220	Cutoff
221	Documents the Meter Flow High Limit
222	Flow Hi
223	Documents the Meter Flow Low Limit
224	Flow Lo
225	Documents the Material Composition of the Meter Body
226	Meter Matl
227	Documents the Meter Pressure Drop Limit
228	Drop Lim
229	Documents the Meter Pressure High Limi
230	Press Hi
231	Documents the Meter Pressure Low Limit
232	Press Lo
233	Documents the Meter Body Size
234	Meter Size
235	Documents the Meter Temperature High Limit
236	Temp Hi
237	Documents the Meter Temperature Low Limit
238	Temp Lo
239	Documents the Model Code for this Meter
240	Model
241	Observed Density. User-Entry for documentation
242	ObsDens
243	Observed Temperature in the process. User-Entry for documentation
244	ObsTemp
245	Observed Viscosity. User-Entry for documentation
246	ObsVisc
247	9.4f
248	Observed Pressure. User-Entry for documentation
249	ObsPres
250	Documents the material code used in the O-Ring, if used
251	O-RingMatl
252	%
253	Units of Measure for Pressure
254	No Help Available
255	Adjusts the number of Output Pulses per Unit of Flow
256	Scaler
257	10.4f
258	Unit of measure assigned to Pulse Output 1
259	ms
260	Sets the on-time width of Output Pulses. Off-time varies with the Output Frequency
261	Width
262	Resettable Totalizer
263	ResTot
264	Resettable Totalizer Number of Digits and Decimal Digits to Display
265	Resettable Totalizer Units of Measure
266	Vol Unit
267	Sequence Number, # of batches run, # of times resettable totalizer was cleared
268	Seq No
269	8i
270	Documents the Serial Number of this Meter
271	Ser No
272	Software Revision
273	Sftwr Rev
274	Units of Measure for Temperature
275	Units of Measure for Viscosity
276	Unit of measure for PV
277	Counts changes to Weights&Measures protected Calibration parameters
278	Calib
279	6i
280	Counts changes to Weights&Measures protected Configuration parameters
281	Config
282	Remote Security Lock
283	Lock
284	Accessories
285	Alarm Config
286	Alarms
287	Analog Output
288	Basic Setup
289	Calibration Info
290	Calibration Points
291	Computations
292	Contact Output 1
293	Contact Output 2
294	Contact O/Ps
295	Dbase Init
296	Detailed Setup
297	Density
298	Device Info
299	Diagnostics
300	Diags & Services
301	Flow
302	Flow Meter
303	HART Output
304	High Flow Rate
305	Internal Temp
306	Inventory
307	Loop Test
308	Low Flow Rate
309	Measurements
310	Meter Calibration
311	Configuration
312	Outputs
313	Power
314	Pressure
315	Process Variables
316	Pulse Out Config
317	Pulse Out Overrun
318	Pulse Out
319	Resettable
320	Revision Info
321	Root Menu
322	Status
323	Temperature
324	Test Device
325	Totalizers
326	Viscosity
327	W & M
328	Loop Notice
329	Notify the operator that the control loop should be returned to automatic
330	Dynamic Edit Notice
331	This value may be being dynamically calulated. Consult Help or Instr.Manual to verify that this edit value will not be automatically overwritten
332	Contact Out Abort
333	Cease testing the Contact Output
334	Contact O/P Test
335	Toggle the Contact Output Off and On
336	Edit Warning
337	Warn the operator that changing this parameter will dramatically affect how other parameters are calculated
338	Puts the Analog Out in manual control. Allows the operator to set the Analog Out value to 4 mA, 20 mA, or return to automatic control.
339	Not Available
340	This feature is not available at this time
341	Pulse Out Abort
342	Terminates the Pulse Output test
343	Pulse O/P Test
344	Manually set the Pulse Output frequencey and the duration of the test. Duration is in seconds. A value of 0 sets the Pulse Output to run continuously
345	Reset Alarm
346	Acknowledge and clear the topmost alarm
347	Reset
348	Clear the resettable totalizer to zero
349	Parameter Limits Exceeded
350	The value of some of the parameter(s) written exceeded the Min or Max limit of the parameter
351	Alarm Status
352	Not Defined
353	Device Diagnostics detected a problem, see Diagnostic Status for more information
354	Database Init
355	The field device interanl database has been initialized to default values
356	A power failure has occured
357	The internal temperature of the device has exceededd maximum limits
358	The flow rate has exceededd device limits
359	The pulse output configuration parameters are in error or confilict
360	The process flow rate has excceded the configured pulse output parameters
361	Diagnostic Status 1
362	RAM Test Fail
363	Field Deivce RAM Memory failed self-test
364	Flash Test Fail
365	Field Device Flash Memory failed sefl-test
366	Dbase Chksum Err
367	Field Device Database failed checksum test
368	PIC Reset
369	Pulse processor has reset
370	PIC Fail
371	Pulse processor has failed
372	Float Position
373	Float Position exceeds configured limits
374	Calibration
375	Calibration parameters are in error or conflict
376	Int Temp Sensor
377	The Field Device Internal Temperature Sensor has failed
378	Turns on or off warning messages associated with editing some variables. Does not turn off the Loop Warning message
379	Warning Level
380	Vol Flow
381	Device Setup
382	write_variables
383	FMU860
384	DT
385	DVC
386	FCX
387	AS800
388	340T
389	340C
390	344
391	Siemens Micro K
392	SITRANS L
393	SIPAN PH
394	SITRANS P
395	75SMT
396	UNIDELTA
397	8320
398	SX5100
399	TSV175
400	DMU
401	3780
402	BM70
403	8u
404	-WARNING- Return control loop to automatic control
405	NOTE: This value may be dynamically calculated. Consult Help for this var. for addl. info
406	Contact O/P Test aborted Contact O/Ps returned to Automatic Control
407	Select Contact O/P
408	1;2;Exit
409	Exiting Test. Contact O/Ps returned to Automatic Control
410	Set Contact O/P #1 State:
411	Off;On;Auto Control;Change Contact O/P
412	Set Contact O/P #2 State:
413	Contact O/P #%{channel} is now Off
414	Contact O/P #%{channel} is now On
415	Contact O/P #%{channel} is now in Automatic Control
416	WARNING: This parameter change will affect transmitter calculations in a significant way.
417	Set Loop Current
418	4 mA;20 mA;Auto Control
419	-WARNING- Pressing 'OK' will change device output. and place the loop in manual.
420	Loop returned to Automatic Control
421	Loop in Manual Control and fixed to selected value
422	Pulse O/P Test aborted
423	Enter Frequency:
424	frequency
425	Value must be between 1.0 and 1000.0 Hz
426	Enter Pulse Count: (0 = Continuous)
427	duration
428	Test will run Continuously
429	Test will run approximately %[8.3f]{RunTime} secs.
430	Sending Continuous Pulses...
431	Running Test....
432	Test Complete
433	Continue;Exit
434	There are no Alarms to clear
435	Resetting Diagnostic Alarm will clear Diagnostic Status Bits
436	Press OK to clear %{0} Alarm
437	Are You Sure?
438	Yes;No
Reference ID	String