Device dictionary

Loading…

Reference ID	String
0	Zero
1	Reset the gas reading to 0 (clean air for all gases except O2 and CO2).
2	Inhibit mode
3	Set or clear inhibit mode.
4	Clear Inhibit mode
5	Clear inhibit mode.
6	Pellistor mode
7	.2f
8	.1f
9	.0f
10	Calibration
11	Calibrate the gas reading to an applied gas level.
12	Zero Trim
13	Trim analogue output 4mA point.
14	Span Adjust
15	Span adjust analogue output to give 20mA with 100% target gas.
16	Clear ramp mode
17	Clear (exit) ramp mode.
18	Ramp auxiliary method
19	Auxiliary method to assist with Ramp with and without alarm.
20	Ramp No Alarm
21	Ramp (manual control) of analogue output for test without alarm relay activation.
22	Ramp With Alarm
23	Ramp (manual control) of analogue output for test with alarm relay activation.
24	Date and Time
25	Set time and date in instrument.
26	Acknowledge Alarms
27	Reset latched alarms.
28	Speedy Bump
29	Check alarm 1 can be exceeded in test time; use Abort to terminate purge when in clean air.
30	Smart Bump
31	Check gas level between defined limits at end of test; use Abort to terminate purge when in clean air.
32	Set
33	Inhibit loop current and alarm relays.
34	Clear
35	Remove inhibit of loop current and alarm relays.
36	Relay Test
37	Test alarm and fault relays.
38	Device Reset
39	Reset XgardIQ and perform all power-on tests.
40	XgardIQ Maintenance
41	XgardIQ Offline
42	XgardIQ Process Variables
43	XgardIQ Diagnostics
44	XgardIQ
45	Inhibit
46	Set or clear inhibit state.
47	Readings
48	Various parameters monitor by the XgardIQ
49	Analogue Output
50	Options to allow adjustment and test of the analogue output system.
51	Alarm 1
52	Options to view and modifiy alarm 1 parameters.
53	Alarm 2
54	Options to view and modifiy alarm 2 parameters.
55	Alarm and Relay
56	Options to view and adjust alarm parameters.
57	Bump Test
58	Options to view and adjust bump test parameters and perform tests.
59	Configure
60	View or modify configuration.
61	Test
62	Options for instrument test.
63	Set Ramp (manual) mode on analogue output.
64	Test sensor response to gas.
65	Revision Numbers
66	Review revision information associated with the field device.
67	HART
68	Review data and information associated with the field device.
69	Review and modify information associated with the field device.
70	Sensitivity
71	Estimated sensor sensitivity, including quality of the information.
72	Information
73	Instrument status, including temperature, supply V, due dates, +ve Safety and other review information.
74	+ve Safety
75	Set +ve safety status data.
76	Status
77	Set device status.
78	Current time and date.
79	Due Dates
80	Dates by which the next bump test and calibration should be performed.
81	About
82	Information about the XgardIQ.
83	Firmware
84	Firmware versions of the XgardIQ components.
85	Fitted Modules
86	Optional modules fitted to XgardIQ.
87	Sensor
88	Details of the fitted sensor module.
89	Cross Gases
90	Gases and associated levels that can be used for a cross calibration or bump.
91	Serial Number
92	Password
93	Options associated with the password lock of instrument modification.
94	Crowcon
95	Configuration locked
96	Configuration locked by password protection.
97	Status 0
98	Initialising
99	Gas alarm 1
100	Gas alarm 2
101	4-20mA signal inhibited
102	4-20mA signal in ramp mode
103	Alarm and fault relays inhibited
104	Alarm relays in test mode
105	Fault relay in test mode
106	Status 1
107	Sensor hardware fault
108	Transmitter hardware fault
109	Sensor firmware fault
110	Transmitter firmware fault
111	Undefined fault in sensor
112	Unused status 1
113	Production failure
114	Analogue output feedback fault
115	Status 2
116	Sensor measurement fault
117	Watchdog test failure
118	Unused status 2
119	Sensor version fault
120	Sensor missing
121	Unused status 3
122	Unused status 4
123	Gas calibration required
124	Status 3
125	Unused status 5
126	Gas calibration data error
127	Gas characterization error
128	Unused status 6
129	Unused status 7
130	Sensor temperature fault
131	Gas reading under range
132	Gas reading over range
133	Status 4
134	Optics obscured
135	Sensor over gassed
136	Unused status 8
137	Unused status 9
138	mA output calibration error
139	Transmitter characterization error
140	Unused status 10
141	Unused status 11
142	Status 5
143	Supply voltage low
144	Supply voltage high
145	Transmitter temperature fault
146	Tramsmitter system fault
147	Sensor system warning
148	Log data error
149	Log data lost
150	Unused status 12
151	Status 6
152	Display missing
153	Display hardware fault
154	Display firmware fault
155	Language data error
156	Display temperature fault
157	Display system warning
158	Unused status 13
159	Biased sensor battery failure
160	Status 7
161	Sensor changed; different gas
162	Sensor changed; same gas
163	Sensor changed; changed rejected
164	Optics nearly obscured
165	Unused status 14
166	Time/data lost
167	Calibration due
168	Calibration due soon
169	Status 8
170	Bump test due
171	Outputs inhibited
172	Unused status 15
173	Internal data error
174	+ve safety data lost
175	Configuration update failed
176	Unused status 16
177	Unused status 17
178	Signal Range
179	0.1f
180	Current Date
181	Current Date based upon the real-time clock in the XgardIQ.
182	Current Time
183	Current Time based upon the real-time clock in the XgardIQ.
184	Set Clock Date
185	Date to set the real-time clock in the field device to, or date that the real-time clock was last set.
186	Set Clock Time
187	Time to set the real time clock in the field device to, or time that the real-time clock was last set.
188	OK
189	Failed: Invalid selection.
190	Failed: XgardIQ received too few bytes.
191	Failed: Password protected. Unlock and re-try.
192	Failed: Access restricted.
193	Sensor successfully zeroed.
194	Zero in progress.
195	Zero succeeded; calibration now required.
196	Failed: Sensor or detector failure.
197	Failed: Optics obscured.
198	Failed: Sensor temperature out of limits.
199	Failed: Pellistor in saver mode.
200	Failed: Sensor supply out of limits.
201	Failed: Reading too far from clean air.
202	Failed: Sensor module missing.
203	Internal failure in XgardIQ! Check status and re-try.
204	Failed: Sensor under/over range.
205	Failed: Bump test or calibration in progress.
206	Failed: Sensor not purged with N2.
207	Sensor successfully calibrated.
208	Failed: Gain low, too much gas applied?
209	Failed: Gain high, too little gas applied?
210	Calibration in progress.
211	Failed: No calibration gas applied.
212	Failed: Production error.
213	Failed: Bump test or zero in progress.
214	Failed: Calibration level invalid.
215	Transmitter Serial Number
216	Serial number of the XgardIQ transmitter.
217	Sensor Serial Number
218	Serial number of the XgardIQ sensor module.
219	Main Firmware Version
220	Software version of the transmitter (main) component of the XgardIQ.
221	Sensor Firmware Version
222	Software version of the XgardIQ sensor module.
223	Display Firmware Version
224	Software version of the transmitter component of the XgardIQ.
225	Enable or disable use of HART password.
226	Disabled
227	Disable password protection
228	Enabled
229	Enable password protection
230	Set Password
231	Password required to unlock a HART password protected instrument.
232	password
233	Password to Unlock
234	Password required to unlock HART password protected instrument.
235
236	Password Lock
237	Current state of password lock.
238	Unlocked
239	XgardIQ password unlocked - write functions are accessible
240	Locked
241	XgardIQ locked by password - unlock to access write functions
242	On Threshold
243	Alarm activiation level
244	Off Threshold
245	Alarm de-activiation level
246	On Delay
247	Delay (in seconds) to alarm activation once on-threshold crossed.
248	Off Delay
249	Delay (in seconds) to alarm de-activation once off-threshold crossed.
250	Latching
251	Specifies if alarm 1 is latched once alarm condition clears.
252	Relay
253	Specifies default state of relay.
254	De-energised
255	Energised
256	Direction
257	Specifies whether alarm is rising or falling.
258	Falling
259	Rising
260	Failed: Invalid alarm selection.
261	Failed: Invalid data or alarm selection
262	Gas Name
263	Configured name of measured gas.
264	Gas Units
265	Configured units of measured gas.
266	ID String
267	XgardIQ identification string.
268	Relays Fitted?
269	Optional fitted component.
270	Not fitted
271	Optional relay board is not fitted.
272	Fitted
273	Optional relay board is fitted.
274	Foundation Fieldbus Fitted?
275	Optional Foundation Fieldbus board is not fitted.
276	Optional Foundation Fieldbus board is fitted.
277	Gas sensor module type.
278	None
279	Toxic
280	Oxygen
281	Biased toxic
282	Pellistor
283	Infra-red
284	MOS
285	PID
286	IRmax
287	Not CO2
288	CO2
289	Failed: Passed parameter too large.
290	Failed: Passed parameter too small.
291	Failed: Loop current not active (device in multi-drop mode).
292	Alarms acknowledged
293	Zero Suppression
294	Level of suppression used to reduced noise around the clean air value.
295	Light
296	Medium
297	Heavy
298	Failed: Invalid data.
299	Saver disabled
300	Saver enabled
301	Pellistor restart request successful.
302	Failed: Invalid option.
303	Gas Sense Time
304	Time instrument will wait for initial gas response before test start. Valid range 5 to 300 seconds.
305	Bump Test Time
306	Maximum test time for speedy bump; total test time for smart bump. Valid range 5 to 300 seconds.
307	Smart Bump Lower Limit
308	Lowest gas reading allowed to pass a smart bump. Valid range 0 to sensor range.
309	Smart Bump Upper Limit
310	Highest gas reading allowed to pass a smart bump. Valid range 0 to sensor range.
311	Bump test not in progress.
312	Waiting for initial gas response.
313	Test in progress
314	Test passed - purging test gas.
315	Test failed - purging gas.
316	Test failed - no purge required.
317	Poll status
318	Speedy test
319	Smart test
320	Terminate test
321	Bump test passed.
322	Failed: Invalid test option.
323	Failed: Password locked; unlock and re-try.
324	Failed: Gas reading too low.
325	Failed: Gas reading too high.
326	Failed: Zero, bump or calibration in progress.
327	Bump test in progress.
328	Failed: Check instrument status.
329	Failed: Gas present at test start.
330	Failed: No gas response.
331	Failed: No alarm during test.
332	Failed: Zero or calibration in progress.
333	Aborted: user request.
334	Bump Due Date
335	Instrument is due for bump test before the end of this date.
336	Calibration Due Date
337	Instrument is due for calibration before the end of this date.
338	Relay Test State.
339	State of alarm and fault relay test.
340	Relay test inactive.
341	Alarm relays: both inactive.
342	Alarm relays: 1 active
343	Alarm relays: 2 active.
344	Alarm relays: both active.
345	Fault relay: active.
346	Fault relay: inactive.
347	Relay test state set.
348	Failed: Relay module not fitted.
349	Fault Level
350	mA signal level when in fault state.
351	1mA
352	2mA
353	3mA
354	Warning Level
355	mA signal level when in warning state.
356	Inhibit Level
357	mA signal level when in operational inhibit state.
358	Clean air
359	Power-on Inhibit
360	mA signal level when in power-on inhibit state.
361	Failed: XgardIQ received too few bytes
362	Number of Cross Gases
363	Number of gases for cross calibration and bump
364	Gas Range
365	Full measurement range of gas sensor.
366	Target gas name.
367	Target gas measurement units.
368	Cross Gas 1 Level
369	Level of cross gas to apply for cross calibration and bump.
370	Cross Gas 1 Name
371	Gas to be used for cross calibration and bump.
372	Cross Gas 1 Units
373	Units of gas to be used for cross calibration and bump.
374	Cross Calbration Factor 1
375	Relative cross sensitivity to target gas.
376	Cross Gas 2 Level
377	Cross Gas 2 Name
378	Cross Gas 2 Units
379	Estimated sensor sensitivity at last successful calibration.
380	Sensitivity Quality
381	Quaility of sensitivity estimate.
382	Unknown, low
383	Sensitivity low - either sensor failed or last calibration incorrectly peformed.
384	Unknown, high
385	Sensitivity high - last calibration incorrectly peformed.
386	Sensitivity estimate is sound.
387	Gas
388	Measured gas level.
389	Engineering unit associated with the measured gas level.
390	%LEL
391	percentage of lower explosive limit (%LEL)
392	%vol
393	volume of target gas as a percentage of volume (%vol)
394	ppm
395	parts per million (ppm)
396	ppb
397	parts per billion (ppb)
398	Gas Class
399	Gas PDQ
400	Gas LS
401	Gas Fmly stat
402	Gas Dev fmly
403	Sensor Range
404	Gas LSL
405	Gas min span
406	Gas damp
407	Gas serial number
408	Gas lower trim
409	Gas upper trim
410	.3f
411	Gas Trim support
412	Gas Min lower trim
413	Gas Max lower trim
414	Gas Min upper trim
415	Gas Max upper trim
416	Gas Min trim diff
417	Sensor Obscuration
418	Obscuration of the optics.
419	Obscuration Units
420	Sensor Obscuration Units- Engineering unit to be displayed with Sensor Obscuration.
421	%
422	Percentage obscuration
423	+ve Safety 1
424	Conditions that have occurred that may have compromised the instrument's ability to accurately measure gas.
425	Pellistor saver occurred
426	Sensor temperature too low
427	Sensor temperature too high
428	+ve Safety 2
429	Conditions that indicate something has happened to the instrument that could have affected it.
430	Loop mode disabled
431	Fault state
432	Warning state
433	Unused status
434	Failed: Busy with zero, calibrate or bump test.
435	Obscuration Class
436	Device_family
437	Obscuration PDQ
438	Obscuration LS
439	Obscuration Dev Stat
440	Obscuration USL
441	Obscuration LSL
442	Obscuration min span
443	Obscuration damp value
444	Obscuration snsr s/n
445	Obscuration
446	Optical obscuration
447	Supply V
448	Instrument supply voltage.
449	Supply V Units
450	Supply V Units- Engineering unit to be displayed with instrument supply voltage.
451	Volts
452	Supply voltage
453	Supply V Class
454	Device family
455	Supply PDQ
456	Supply LS
457	Temp Dev Stat
458	Supply USL
459	Supply LSL
460	Supply min span
461	Supply damp value
462	Temp snsr s/n
463	Gas (no zero suppression)
464	Measured gas level with no zero suppression.
465	Gas units
466	Sensor Temperature
467	Temperature as measured by the sensor module.
468	Temperature Units
469	Sensor Temperature Units- Engineering unit to be displayed with Sensor Temperature.
470	ºC
471	Temperature
472	Temperature Class
473	Temperature PDQ
474	Temperature LS
475	Temperature Dev Stat
476	Temperature USL
477	Temperature LSL
478	Temperature as measured by the sensor module
479	temperature
480	Transmitter Temperature
481	Temperature as measured by the transmitter.
482	Units
483	Transmitter Temperature Units- Engineering unit to be displayed with Transmitter Temperature.
484	Temperature as measured by the transmitter
485	Gas (no suppression)
486	Transmitter
487	PV Analog Channel Saturated
488	PV Analog Channel Fixed
489	Wireless
490	WirelessHART Device
491	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
492	Primary
493	Primary Analog Channel
494	Secondary
495	Secondary Analog Channel
496	Tertiary
497	Tertiary Analog Channel
498	Quaternary
499	Quaternary Analog Channel
500	Quinary
501	Quinary Analog Channel
502	Critical Power Failure
503	Lock all
504	Trim not supported
505	Configuration cannot be changed
506	Locked by gateway
507	Analog Input Channel
508	Analog Output Channel
509	Secondary Analog Channel Saturated
510	Tertiary Analog Channel Saturated
511	Quaternary Analog Channel Saturated
512	Quinary Analog Channel Saturated
513	Secondary Analog Channel Fixed
514	Tertiary Analog Channel Fixed
515	Quaternary Analog Channel Fixed
516	Quinary Analog Channel Fixed
517	Simulation active
518	The device is in simulation mode and the level output is not representative of the process.
519	Non-Volatile memory failure
520	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
521	Volatile memory error
522	The RAM memory check is invalid or maybe corrupt
523	Watchdog reset executed
524	A watchdog reset has been performed
525	Voltage conditions out of range
526	A voltage condition is outside its allowable range
527	Environmental conditions out of range
528	An internal or environmental condition is beyond acceptable limits.
529	Electronic failure
530	A hardware problem not related to the sensor has been detected.
531	Subdevice list changed
532	Duplicate master detected
533	Capacity Denied
534	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
535	Bandwidth allocation pending
536	Block transfer pending
537	Battery life
538	Percent range
539	Loop current
540	Primary variable
541	Secondary variable
542	Tertiary variable
543	Quaternary variable
544	Read receive time
545	Write date and time
546	Non-Volatile Clock
547	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
548	Clock Uninitialized
549	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
550	No restrictions
551	SI Only
552	Restricted to SI Unit codes only
553	Process automation device
554	Discrete device
555	Hybrid:Process automation+discrete
556	I/O System
557	WirelessHART Process automation device
558	WirelessHART Discrete device
559	WirelessHART Process automation+discrete
560	WirelessHART Gateway
561	WirelessHART Access point
562	WirelessHART Process adapter
563	WirelessHART Discrete adapter
564	WirelessHART enabled handheld/portable maintenance tool
565	Device Profile
566	US
567	United States of America
568	JP
569	Japan
570	DE
571	Germany
572	FR
573	France
574	ES
575	Spain
576	RU
577	Russian Federation
578	CN
579	People's Republic of China
580	Secondary Master
581	Primary Master
582	Device Diagnostic Status 0
583	Device Diagnostic Status 1
584	I/O and Subdevice Status
585	WirelessHART Status
586	Time Set Option
587	Real Time Clock Flags
588	Country
589	Country of intended device installation
590	SI Unit Control
591	Indicates if device should only display SI unit codes
592	Time Stamp
593	Relative time value on network
594	8u
595	Dynamic Variables Returned for Device Variables
596	Command Response Truncated
597	Configuration Change Counter Mismatch
598	Status bytes mismatch
599	8.3f
600	WARNING: Abort only aborts the HART master. Selected operation will still complete.
601	Purge sensor with nitrogen and select OK when ready. Gas level: %[D]{varGasNoSuppressValue} %{varGasCfgUnits}
602	Ensure in clean air and select OK when ready. Gas level: %[D]{varGasNoSuppressValue} %{varGasCfgUnits}
603	Performing zero, please wait...0% complete.
604	Performing zero, please wait...%[d]{varIntZeroProgress}% complete.
605	Purge nitrogen from sensor and select OK when gas is cleared. Gas level: %[D]{varGasNoSuppressValue} %{varGasCfgUnits}
606	level1
607	%{varGasCfgName};%{varSensorXName_1} %{level1} %{varSensorXUnits_1}
608	Select gas to use
609	level2
610	%{varGasCfgName};%{varSensorXName_1} %{level1} %{varSensorXUnits_1};%{varSensorXName_2} %{level2} %{varSensorXUnits_2}
611	Calibration gas to be applied (%{varGasCfgUnits}):
612	Apply calibration gas of %{calGas} and select OK when ready. Gas level: %[D]{varGasNoSuppressValue} %{varGasCfgUnits}
613	Performing calibration, please wait...0% complete.
614	Performing calibration, please wait...%[d]{varIntCalProgress}% complete.
615	Purge gas from sensor and select OK when gas is cleared. Gas level: %[D]{varGasNoSuppressValue} %{varGasCfgUnits}
616	Successfully cross-calibrated to %{varXCalLvl1} %{varGasCfgUnits} %{varGasCfgName}.
617	Successfully calibrated to %{varCalibrateLvl} %{varGasCfgUnits} %{varGasCfgName}.
618	Loop current will be set to 4mA.
619	mA;%{varGasCfgUnits}
620	Select units for zero trim:
621	Measured loop current (mA):
622	Gas level at control panel (in %{varGasCfgUnits})
623	Loop current will be set to 20mA.
624	Select units for span adjust:
625	Measure loop current using accurate DVM. Measured loop current (mA):
626	Enter the gas level displayed by the control panel. Measured gas level %{varGasCfgUnits}:
627	Use what units for ramp?
628	Enter mA output (0.0 to abort):
629	editLvl
630	Enter %{varGasCfgUnits} output (< 0 to abort):
631	New date (mm/dd/yyyy):
632	New time (hh:mm:ss):
633	Alarms successfully acknowledged.
634	level
635	%{varGasCfgName};%{varSensorXName_1} %{level} %{varSensorXUnits_1}
636	Ensure the sensor is in clean air and select OK when ready. Gas level: %[D]{varGasNoSuppressValue} %{varGasCfgUnits}
637	Waiting for gas response... Gas level: %{varGasNoSuppressValue} %{varGasCfgUnits} (%[d]{varIntBumpProgress} seconds left).
638	Performing test... Gas level: %{varGasNoSuppressValue} %{varGasCfgUnits} (%[d]{varIntBumpProgress} seconds left).
639	Remove applied gas... Gas level: %{varGasNoSuppressValue} %{varGasCfgUnits}.
640	Inhibit mode set.
641	Inhibit mode cleared.
642	Relay test to perform
643	Test inactive; Alarm - both inactive; Alarm - 1 active; Alarm - 2 active; Alarm - both active; Fault - active; Fault - inactive
644	Select OK to reset the device.
645	Waiting for reset...%{i}
646	Reset successful.
Reference ID	String