| 0 |
ST100 Product of Family |
| 1 |
Fluid Components International |
| 2 |
Operation Status |
| 3 |
Serious Device Error |
| 4 |
Electronics Hardware Failure |
| 5 |
Memory Error |
| 6 |
Measurement Failure |
| 7 |
Maintenance Required |
| 8 |
FRAM Failure |
| 9 |
Power Supply Failed |
| 10 |
Configuration Invalid |
| 11 |
Device Initialization Failed |
| 12 |
Device Not Initialized |
| 13 |
Electronic Temperature Too High |
| 14 |
Flow Sensor Failure |
| 15 |
Flow Sensor Not Connected |
| 16 |
Sensor Communication Error |
| 17 |
Totalizer Overflow |
| 18 |
Flow Is Out Of Range |
| 19 |
Ethernet Communication Failure |
| 20 |
USB Communication Failure |
| 21 |
Industrial Communication Protocol Failure |
| 22 |
Process Temperature Over Max Limit |
| 23 |
Process Temperature Under Min Limit |
| 24 |
Flow Sensor Heater #1 Shorted |
| 25 |
Flow Sensor #2 Shorted |
| 26 |
Flow Sensor #1 Open |
| 27 |
Flow Sensor Heater #2 Open |
| 28 |
Flow Sensor A/D Counts Exceed Max Limit |
| 29 |
Flow Sensor A/D Counts Dropped Below Min Limit |
| 30 |
Flow Sensor Signal Exceeds 120% Signal Limit |
| 31 |
Flow Sensor Signal Exceeds 100% Signal Limit |
| 32 |
Flow Sensor Signal Exceeds A/D Convertor Limit |
| 33 |
FE Component Error -AD5627 |
| 34 |
FE Component Error - TMP100 |
| 35 |
FE Component Error - AD5754 |
| 36 |
FE Component Error - ACT/REF Sensor A//D |
| 37 |
FE Component Error - Current Sensors A/D |
| 38 |
FE Component Error - GRND Ret & Pressure Sensor A/D |
| 39 |
FE Component Error - Heaters I Sensors A/D |
| 40 |
FE Component Error - ARM7 Undefined Fault |
| 41 |
FE Component Error - ARM7 SWI Fault |
| 42 |
FE Component Error - ARM7 Prefetch Abort Fault |
| 43 |
FE Component Error - ARM7 Data Abort Fault |
| 44 |
FE Component Error - ARM7 FIQ Fault |
| 45 |
FE Component Error - ARM7 Spurious INT Fault |
| 46 |
STACK in Self Check Mode - No Process Data Available |
| 47 |
Volume Flow |
| 48 |
Volume |
| 49 |
Mass Flow |
| 50 |
Mass |
| 51 |
Velocity Flow |
| 52 |
Temperature |
| 53 |
Pressure |
| 54 |
Flow minimum span |
| 55 |
.3f |
| 56 |
8.3f |
| 57 |
Flow serial number |
| 58 |
7d |
| 59 |
USL |
| 60 |
LSL |
| 61 |
Flow - measured flow through the pipe |
| 62 |
Flow Value |
| 63 |
Flow Value Unit |
| 64 |
Engr. Units |
| 65 |
Flow Class |
| 66 |
Flow PDQ |
| 67 |
Flow LS |
| 68 |
Flow Fmly stat |
| 69 |
Volume |
| 70 |
Measures Volume Total |
| 71 |
Volume Total |
| 72 |
Mass Total |
| 73 |
Measured Volume Total |
| 74 |
Measured Mass Total |
| 75 |
0.2f |
| 76 |
Total Units |
| 77 |
Totalizer Class |
| 78 |
Volume PDQ |
| 79 |
Volume LS |
| 80 |
Volume LSL |
| 81 |
TNSS |
| 82 |
Mass |
| 83 |
Mass Class |
| 84 |
Totalizer PDQ |
| 85 |
Mass LS |
| 86 |
Totalizer LSL |
| 87 |
Velocity Flow Value |
| 88 |
SFPH |
| 89 |
SFPD |
| 90 |
SMPM |
| 91 |
SMPD |
| 92 |
Secondary Variable - Temperature Compensation |
| 93 |
.1f |
| 94 |
Snsr temp unit |
| 95 |
Sensor Temperature Units- Engineering unit to be displayed with Sensor Temperature. |
| 96 |
Temp Class |
| 97 |
Temp PDQ |
| 98 |
|
| 99 |
Temperature LS |
| 100 |
Temp Dev Stat |
| 101 |
Minimum span |
| 102 |
Temp snsr s/n |
| 103 |
bar G |
| 104 |
kPa G |
| 105 |
Pres Class |
| 106 |
Pres PDQ |
| 107 |
Pres LS |
| 108 |
Pres Fmly stat |
| 109 |
Totalizer Dev Stat |
| 110 |
Totalizer OFF |
| 111 |
Totalizer ON |
| 112 |
Device CO |
| 113 |
Device Serial Number |
| 114 |
Device SW Version |
| 115 |
CLI Flow Units |
| 116 |
SCFS |
| 117 |
SCFM |
| 118 |
SCFH |
| 119 |
SCFD |
| 120 |
NCMS |
| 121 |
NCMM |
| 122 |
NCMH |
| 123 |
NCMD |
| 124 |
NLPS |
| 125 |
NLPM |
| 126 |
NLPH |
| 127 |
NLPD |
| 128 |
ACFS |
| 129 |
AFPM |
| 130 |
AFPH |
| 131 |
AFPD |
| 132 |
ACMS |
| 133 |
ACMM |
| 134 |
ACMH |
| 135 |
ACMD |
| 136 |
ALTS |
| 137 |
ALTM |
| 138 |
ALTH |
| 139 |
ALTD |
| 140 |
LBPS |
| 141 |
LBPM |
| 142 |
LBPH |
| 143 |
LBPD |
| 144 |
KGPS |
| 145 |
KGPM |
| 146 |
KGPH |
| 147 |
KGPD |
| 148 |
TNNS |
| 149 |
TNNM |
| 150 |
TNNH |
| 151 |
TNND |
| 152 |
SFPS |
| 153 |
SFPM |
| 154 |
NMPS |
| 155 |
NMPM |
| 156 |
NMPH |
| 157 |
NMPD |
| 158 |
AFPS |
| 159 |
AMPS |
| 160 |
AMPM |
| 161 |
AMPH |
| 162 |
AMPD |
| 163 |
CLI Temp. Units |
| 164 |
DEG C |
| 165 |
DEG F |
| 166 |
CLI Total Units |
| 167 |
Std Cu Ft |
| 168 |
Act Cu Ft |
| 169 |
Norm Cu Mtr |
| 170 |
Act Cu Mtr |
| 171 |
Liters |
| 172 |
Act Liters |
| 173 |
Pounds |
| 174 |
Kilograms |
| 175 |
Tonnes |
| 176 |
CLI Press. Units |
| 177 |
psiA |
| 178 |
psiG |
| 179 |
in H20 G |
| 180 |
in Hg |
| 181 |
bar A |
| 182 |
kPa A |
| 183 |
cm H20 G |
| 184 |
mm Hg |
| 185 |
torr A |
| 186 |
Plenum Height Value |
| 187 |
Plenum Width (Diameter) Value |
| 188 |
Plenum Unit |
| 189 |
millimeter |
| 190 |
inches |
| 191 |
Write Protection |
| 192 |
Disable Write Protection |
| 193 |
Enable Write Protection |
| 194 |
Flow Lower Limit |
| 195 |
Flow Lower Limit Value |
| 196 |
Flow Upper Limit |
| 197 |
Flow Upper Limit Value |
| 198 |
Temp Lower Limit |
| 199 |
Temp Lower Limit Value |
| 200 |
Temp Upper Limit |
| 201 |
Temp Upper Limit Value |
| 202 |
Press Lower Limit |
| 203 |
Press Lower Limit Value |
| 204 |
Press Upper Limit |
| 205 |
Press Upper Limit Value |
| 206 |
Factory Reset |
| 207 |
Channel 1 DA Setting for 4mA |
| 208 |
Channel 1 DA Setting for 20mA |
| 209 |
Channel 1 Out Variable |
| 210 |
Off |
| 211 |
Flow |
| 212 |
Channel 2 DA Setting for 4mA |
| 213 |
Channel 2 DA Setting for 20mA |
| 214 |
Channel 2 Out Variable |
| 215 |
Channel 3 DA Setting for 4mA |
| 216 |
Channel 3 DA Setting for 20mA |
| 217 |
Channel 3 Out Variable |
| 218 |
Factory Reset |
| 219 |
Set/Reset Write Protection Flag |
| 220 |
Select Primary Variable |
| 221 |
Measured Values |
| 222 |
Start |
| 223 |
ST100 Process Data |
| 224 |
Device ID |
| 225 |
ST100 Status |
| 226 |
DEVICE STATUS |
| 227 |
FCI STAT BYTE 0 |
| 228 |
FCI STAT BYTE 1 |
| 229 |
FCI STAT BYTE 2 |
| 230 |
FCI STAT BYTE 3 |
| 231 |
FCI STAT BYTE 4 |
| 232 |
FCI STAT BYTE 5 |
| 233 |
ST100 BASIC SETUP |
| 234 |
ST100 CONFIGURATION |
| 235 |
ST100 FACTORY CALIBRATION LIMITS |
| 236 |
UNITS |
| 237 |
PLENUM |
| 238 |
TOTALIZER |
| 239 |
DEVICE INFO |
| 240 |
FACTORY RESET |
| 241 |
WRITE PROTECTION |
| 242 |
PV SETUP |
| 243 |
Channel 1 Setup |
| 244 |
Channel 2 Setup |
| 245 |
Channel 3 Setup |
| 246 |
INSTRUMENT FLOW LIMITS |
| 247 |
INSTRUMENT TEMPERATURE LIMITS |
| 248 |
INSTRUMENT PRESSUE LIMITS |
| 249 |
PV Analog Channel Saturated |
| 250 |
PV Analog Channel Fixed |
| 251 |
Wireless |
| 252 |
WirelessHART Device |
| 253 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 254 |
Primary |
| 255 |
Primary Analog Channel |
| 256 |
Secondary |
| 257 |
Secondary Analog Channel |
| 258 |
Tertiary |
| 259 |
Tertiary Analog Channel |
| 260 |
Quaternary |
| 261 |
Quaternary Analog Channel |
| 262 |
Quinary |
| 263 |
Quinary Analog Channel |
| 264 |
Critical Power Failure |
| 265 |
Lock all |
| 266 |
Trim not supported |
| 267 |
Configuration cannot be changed |
| 268 |
Locked by gateway |
| 269 |
Analog Input Channel |
| 270 |
Analog Output Channel |
| 271 |
Secondary Analog Channel Saturated |
| 272 |
Tertiary Analog Channel Saturated |
| 273 |
Quaternary Analog Channel Saturated |
| 274 |
Quinary Analog Channel Saturated |
| 275 |
Secondary Analog Channel Fixed |
| 276 |
Tertiary Analog Channel Fixed |
| 277 |
Quaternary Analog Channel Fixed |
| 278 |
Quinary Analog Channel Fixed |
| 279 |
Simulation active |
| 280 |
The device is in simulation mode and the level output is not representative of the process. |
| 281 |
Non-Volatile memory failure |
| 282 |
The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed. |
| 283 |
Volatile memory error |
| 284 |
The RAM memory check is invalid or maybe corrupt |
| 285 |
Watchdog reset executed |
| 286 |
A watchdog reset has been performed |
| 287 |
Voltage conditions out of range |
| 288 |
A voltage condition is outside its allowable range |
| 289 |
Environmental conditions out of range |
| 290 |
An internal or environmental condition is beyond acceptable limits. |
| 291 |
Electronic failure |
| 292 |
A hardware problem not related to the sensor has been detected. |
| 293 |
Subdevice list changed |
| 294 |
Duplicate master detected |
| 295 |
Capacity Denied |
| 296 |
The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified |
| 297 |
Bandwidth allocation pending |
| 298 |
Block transfer pending |
| 299 |
Battery life |
| 300 |
Percent range |
| 301 |
Loop current |
| 302 |
Primary variable |
| 303 |
Secondary variable |
| 304 |
Tertiary variable |
| 305 |
Quaternary variable |
| 306 |
Read receive time |
| 307 |
Write date and time |
| 308 |
Non-Volatile Clock |
| 309 |
When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure. |
| 310 |
Clock Uninitialized |
| 311 |
The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device. |
| 312 |
None |
| 313 |
No restrictions |
| 314 |
SI Only |
| 315 |
Restricted to SI Unit codes only |
| 316 |
Process automation device |
| 317 |
Discrete device |
| 318 |
Hybrid:Process automation+discrete |
| 319 |
I/O System |
| 320 |
WirelessHART Process automation device |
| 321 |
WirelessHART Discrete device |
| 322 |
WirelessHART Process automation+discrete |
| 323 |
WirelessHART Gateway |
| 324 |
WirelessHART Access point |
| 325 |
WirelessHART Process adapter |
| 326 |
WirelessHART Discrete adapter |
| 327 |
WirelessHART enabled handheld/portable maintenance tool |
| 328 |
Device Profile |
| 329 |
US |
| 330 |
United States of America |
| 331 |
JP |
| 332 |
Japan |
| 333 |
DE |
| 334 |
Germany |
| 335 |
FR |
| 336 |
France |
| 337 |
ES |
| 338 |
Spain |
| 339 |
RU |
| 340 |
Russian Federation |
| 341 |
CN |
| 342 |
People's Republic of China |
| 343 |
Secondary Master |
| 344 |
Primary Master |
| 345 |
Device Diagnostic Status 0 |
| 346 |
Device Diagnostic Status 1 |
| 347 |
I/O and Subdevice Status |
| 348 |
WirelessHART Status |
| 349 |
Time Set Option |
| 350 |
Real Time Clock Flags |
| 351 |
Country |
| 352 |
Country of intended device installation |
| 353 |
SI Unit Control |
| 354 |
Indicates if device should only display SI unit codes |
| 355 |
Time Stamp |
| 356 |
Relative time value on network |
| 357 |
8u |
| 358 |
Dynamic Variables Returned for Device Variables |
| 359 |
Command Response Truncated |
| 360 |
Configuration Change Counter Mismatch |
| 361 |
Status bytes mismatch |
| 362 |
Do you want to reset parameters to factory values? |
| 363 |
No;Yes |
| 364 |
Not reset to Factory default values, aborting. |
| 365 |
This will reset to Factory default values. Proceed? |
| 366 |
Unexpected error, device not set to Factory default values, aborting |
| 367 |
Reset to Factory default values. |
| 368 |
Do you want to change write protect? |
| 369 |
Write protect not changed, aborting. |
| 370 |
This will change Write Protect. Proceed? |
| 371 |
Select write protection |
| 372 |
Unexpected error, Write Protection not chaned aborting |
| 373 |
Write Protect Disabled. |
| 374 |
Write Protect Enabled. |
| 375 |
Write Protection has been changed.
Please close setup window and re-open for proper operation. |
| 376 |
Select Primary Variable |
| 377 |
Volume Flow;Mass Flow;Velocity Flow |
| 378 |
Please Wait |
| 379 |
Primary Variable has been changed.
Please close setup window and re-open for proper display of values. |