HART设备字典

Loading…

引用ID	字符串
0	Sensor lines
1
2	2 wire system
3	2 wire system help
4	3 wire system
5	3 wire system help
6	4 wire system
7	4 wire system help
8	Sensor type
9	PT100
10	PT100 help
11	PT1000
12	PT1000 help
13	Thermocouple type B
14	Thermocouple type B help
15	Thermocouple type J
16	Thermocouple type J help
17	Thermocouple type K
18	Thermocouple type K help
19	Thermocouple type R
20	Thermocouple type R help
21	Thermocouple type S
22	Thermocouple type T
23	Invalid sensor type
24	Invalid connection method
25	Factory reset
26	Sensor type or wire connection is incorrect
27	TwoWrie ZeroTrim
28	Temper Trim Value
29	Sensor type error
30	Temperature unit code error
31	Temper Trim
32	CT-PT4550
33	CURTO
34	FLASH Test Error
35	ROM Test Error
36	RAM Test Error
37	CPU Test Error
38	Exceed the range of the sensor
39	Exceed the upper limit of the primary variable
40	Exceed the lower limit of the primary variable
41	Sensor open circuit
42	Loop current too high
43	Loop current too low
44	RESERVED
45	.3f
46	Snsr temp unit
47	Sensor Temperature Units- Engineering unit to be displayed with Sensor Temperature.
48	Temp Class
49	Temp PDQ
50	Temp LS
51	Temp Dev Stat
52	Temp USL
53	Temp LSL
54	Temp min span
55	8.3f
56	Temp snsr s/n
57	7d
58	Secondary Variable - Temperature Compensation
59	current_Value
60	digital_value_current_help
61	current_value_unit
62	digital_units_current_help
63	current Class
64	current PDQ
65	current LS
66	current Fmly stat
67	current
68	current_help
69	Current
70	Temperature
71	Device settings
72	Diagnostics
73	Maintenance
74	Offline
75	Operate
76	Temperature sensor
77	Current sensor
78	Temperature Transmitter Image
79	This is an IMAGE
80	Dynamic Variables
81	PV
82	SV
83	PV Analog Channel Saturated
84	PV Analog Channel Fixed
85	Wireless
86	WirelessHART Device
87	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
88	Primary
89	Primary Analog Channel
90	Secondary
91	Secondary Analog Channel
92	Tertiary
93	Tertiary Analog Channel
94	Quaternary
95	Quaternary Analog Channel
96	Quinary
97	Quinary Analog Channel
98	Critical Power Failure
99	Lock all
100	Trim not supported
101	Configuration cannot be changed
102	Locked by gateway
103	Analog Input Channel
104	Analog Output Channel
105	Secondary Analog Channel Saturated
106	Tertiary Analog Channel Saturated
107	Quaternary Analog Channel Saturated
108	Quinary Analog Channel Saturated
109	Secondary Analog Channel Fixed
110	Tertiary Analog Channel Fixed
111	Quaternary Analog Channel Fixed
112	Quinary Analog Channel Fixed
113	Simulation active
114	The device is in simulation mode and the level output is not representative of the process.
115	Non-Volatile memory failure
116	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
117	Volatile memory error
118	The RAM memory check is invalid or maybe corrupt
119	Watchdog reset executed
120	A watchdog reset has been performed
121	Voltage conditions out of range
122	A voltage condition is outside its allowable range
123	Environmental conditions out of range
124	An internal or environmental condition is beyond acceptable limits.
125	Electronic failure
126	A hardware problem not related to the sensor has been detected.
127	Subdevice list changed
128	Duplicate master detected
129	Capacity Denied
130	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
131	Bandwidth allocation pending
132	Block transfer pending
133	Battery life
134	Percent range
135	Loop current
136	Primary variable
137	Secondary variable
138	Tertiary variable
139	Quaternary variable
140	Read receive time
141	Write date and time
142	Non-Volatile Clock
143	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
144	Clock Uninitialized
145	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
146	None
147	No restrictions
148	SI Only
149	Restricted to SI Unit codes only
150	Process automation device
151	Discrete device
152	Hybrid:Process automation+discrete
153	I/O System
154	WirelessHART Process automation device
155	WirelessHART Discrete device
156	WirelessHART Process automation+discrete
157	WirelessHART Gateway
158	WirelessHART Access point
159	WirelessHART Process adapter
160	WirelessHART Discrete adapter
161	WirelessHART enabled handheld/portable maintenance tool
162	Device Profile
163	US
164	United States of America
165	JP
166	Japan
167	DE
168	Germany
169	FR
170	France
171	ES
172	Spain
173	RU
174	Russian Federation
175	CN
176	People's Republic of China
177	Secondary Master
178	Primary Master
179	Device Diagnostic Status 0
180	Device Diagnostic Status 1
181	I/O and Subdevice Status
182	WirelessHART Status
183	Time Set Option
184	Real Time Clock Flags
185	Country
186	Country of intended device installation
187	SI Unit Control
188	Indicates if device should only display SI unit codes
189	Time Stamp
190	Relative time value on network
191	8u
192	Dynamic Variables Returned for Device Variables
193	Command Response Truncated
194	Configuration Change Counter Mismatch
195	Status bytes mismatch
196	All parameters will be restored to factory values. Are you sure you want to restore the factory value?
197	Successful factory reset!
198	The current value is used as the compensation value of the two-wire system of the RTD type sensor. Is it necessary to perform this method? The external circuit ensures that it is connected.
199	Successful Zero Calibration of Two Wrie!
200	Are you sure you want to calibrate the temperature of the thermocouple?
201	Please enter the standard temperature value.
引用ID	字符串