方法列表 - BERTHOLD - LB480 LevelSwitch-A17B

Loading…

名称	ID	标签	描述	类型	源代码
meth_ResetConfigurationChangeFlag	4242	Reset Modification Flag		msrc_UNKNOWN	详细信息
meth_SWReset	4243	Software Reset	Software Reset This method performs a software reset on the active probe.	msrc_UNKNOWN	详细信息
meth_FactoryReset	4244	Factory Reset	Factory Reset This method performs a factory reset on the active probe.	msrc_UNKNOWN	详细信息
meth_ResetErrorLog	4245	Reset Error Log		msrc_UNKNOWN	详细信息
meth_AcknowlegeError	4246	Acknowledge Error		msrc_UNKNOWN	详细信息
meth_ResetModificationLog	4247	Reset Modification Log		msrc_UNKNOWN	详细信息
meth_SetSafetyModeOff	4248	Safety OFF	Safety OFF Disables the safety mode. Keep the password handy in case you want to make changes, because you will need any time you make changes. If you disable the safety mode, the following settings are made automatically: - the detector is unlocked, i.e. Write Protect is set to OFF - Error Handling is set to NORMAL - Response Mode is set to DISABLED	msrc_UNKNOWN	详细信息
meth_RefreshPlateau	4249	Refresh Plateau	Refresh Plateau Read values from device and refresh graphical view of plateau table.	msrc_UNKNOWN	详细信息
meth_RefreshErrorLog	424A	Refresh Error Log		msrc_UNKNOWN	详细信息
meth_RefreshModificationLog	424B	Refresh Modification Log		msrc_UNKNOWN	详细信息
meth_SetPollingAddress	424C	Set Poll Addr		msrc_UNKNOWN	详细信息
meth_SetPollingAddress_abort	424D			msrc_UNKNOWN	详细信息
meth_SetLicenseKey	424E	Set License Key		msrc_UNKNOWN	详细信息
meth_SetLicenseKey_abort	424F			msrc_UNKNOWN	详细信息
meth_RefreshSafetyStatuses	4250	Refresh Safety Statuses		msrc_UNKNOWN	详细信息
meth_SetSafetyModeOn	4251	Safety ON	Safety ON The safety mode has to be enabled for safety-relevant applications. In safety mode, safety-limiting values are set to a safety-compatible setting. In addition, you will be prompted to protect the detector with a password. The following settings are set automatically when safety mode is enabled: Current Loop Monitoring: = ENABLED HV Mode = AUTO Test Settings = NORMAL Error Handling = SENSITIV Digital inputs: = OFF Multidrop: Poll Addr = 0	msrc_UNKNOWN	详细信息
meth_ReadIn	4252	ReadIn	ReadIn Start reading-in the count rates. While the count rate is read in, the average is calculated and displayed continuously. Under "ReadIn Time" you define the read-in period. First choose which calibration point you want to read in: BACKGROUND The background radiation has to be measured so that the detector can correctly compensate for the decay of the radiation source. Before taking measurements, make sure you do not measure any radiation from the radiation source The easiest way to ensure this is if the source is not yet mounted. Otherwise, close the beam path and fill the container in addition. LOWER-PT For this measurement, the level in the tank must be below the monitoring level or the tank must be completely empty. UPPER-PT This measurement can only be performed at a 2-point calibration. For the measurement, the level in the tank must be above the monitoring level or the tank must be completely filled.	msrc_UNKNOWN	详细信息
meth_ReadIn_abort	4253			msrc_UNKNOWN	详细信息
meth_Calibrate	4254	Calibrate	Calibrate With this menu item you enable the calibration data determined during the measurements. The calibration data are transferred to "Meas Parameter". Thus, the detector will get a new calibration which in the future will be used to determine the measured values. After the calibration, a status message is displayed, indicating if the activation of the calibration data has been carried out successfully. If not, the measurement parameters are unchanged.	msrc_UNKNOWN	详细信息
meth_CalibrateAndPreset	4255	Calibrate + Preset	Calibrate + Preset With this menu item you enable the calibration data determined during the measurements. In this case, the calibration data are transferred to "Meas Parameter". Thus, the detector will get a new calibration which in the future will be used to determine the measured values. After the calibration, a status message is displayed, indicating if the activation of the calibration data has been carried out successfully. If not, the measurement parameters are unchanged. The following settings are made automatically at Calibrate + Auto Set: Evaluation Mode = AUTO SET OP Gas Density = 0 Setup Gas Density = 0 Bulk Cone = 0	msrc_UNKNOWN	详细信息
meth_Restore	4256	Restore Upload	Restore Upload Has a similar function as "Calibrate", but considers a validity date, for example, of older calibration data and automatically performs a decay compensation. First, you have to save the original set of parameters in the HOST or the HART® Communicator as off-line parameters. The off-line parameters can then be restored to the detector. Then enable this parameter set with Restore Upload. The validity date (Restore Date) of the calibration, which is contained in the off-line parameters, will automatically be compared with the current date in the detector and the calibration count rate is adjusted accordingly.	msrc_UNKNOWN	详细信息
meth_Recall	4257	Recall	Recall Recall allows you to copy the current data set from Meas Parameter to Cal Parameter. This allows you to revise the valid parameters, without this having an influence on the measurement at first. After you have finished editing, you can activate the changed settings with "Calibrate". Recall is also necessary because the count rates in the calibration parameters (Cal Parameter) in contrast to the count rates of the measuring parameters (Meas Parameter) are not decay compensated. Important: "Recall" overwrites all settings of the "Cal Parameter" menu.	msrc_UNKNOWN	详细信息
return_to_normal	1016	中止返回正常		msrc_UNKNOWN	详细信息
leave_fixed_current_mode	1003	退出固定电流模式	退出固定电流模式——使选择的模拟量输出退出输出为常数值的模式，使输出返回输出跟踪输入的模式。	msrc_UNKNOWN	详细信息
warning_message	1017	设置回路为手动		msrc_UNKNOWN	详细信息
transmitter_loop_test	1023	Loop test	回路测试——允许用户将选择的模拟量输出手动调节至选择的常数输出值。	msrc_UNKNOWN	详细信息
transmitter_dac_trim	1024	D/A trim	D/A trim Allows you to adjust the current output. You will need a current meter which has to be connected to the current loop. A method will take you through the adjustment.	msrc_UNKNOWN	详细信息
lock_unlock_device	1073	Lock/Unlock Device	锁定/解锁设备——将设备置于锁定或解锁位置。	msrc_UNKNOWN	详细信息
名称	ID	标签	描述	类型	源代码